Availability of Custom Wiring Harness for 2026 Subaru Forester

Question

Question:

I have a 2026 Subaru Forester Wilderness. Talking to the Subaru dealer it takes a H771SSL200 Subaru wire harness. Is Curt or someone working on an after market harness?

asked by: Steven M

0

Expert Reply:

Hi Steven; I believe there was a change in the wiring for the 2026 model that doesn't allow the previous custom wiring to cross over. I'm sure Curt is working on a new wiring harness but we don't have an ETA on when that might be available.

The only aftermarket option right now is the universal 4-way # C59496. This is a splice-in installation instead of a plug in, but will still give you a 4-way to power the lights on your trailer.

Do you already have a hitch and ball mount?

expert reply by: Robin H

0

Curt Wiring Harness
(click to enlarge)

Steven M.

2/18/2026

I do Robin. I'll have to wait for the plug and play or bite the bullet and buy the EOM. Thanks, Steve

Robin H.

2/18/2026

@StevenM yeah the OEM is typically overpriced by a lot, but it is your best bet for now if you don't want to splice and need to tow something in the near future.

Answer 1

Hello Mike, Thanks for writing in, that is a great question. No, you do not need to disable the hands-free liftgate sensor before installing a hitch on your 2026 Subaru Forester. In fact, we've found that the sensor continues to work after the…

view full answer...

Answer 2

Hey Tom! The only covers we have for your 2010 Roadtrek 190 Popular are the etrailer Bucket Seat Protector for Active Lifestyle #e99048 you were looking at. These are universal seat covers so they work for pretty much any bucket seat. If you're…

view full answer...

Answer 3

Hey Lawrence, thanks for reaching out. The Curt T-Connector #C56040 is correct for the 2025 Subaru Forester Hybrid. The factory harness plug should be in the rear cargo area behind the driver side access panel. If you remove the trunk floor covering…

view full answer...

Answer 4

Hey Jim, so the hitches we offer for your 2025 Subaru Forester like the Curt part #C13409 that you referenced do not require deactivating the rear kick sensors for the rear hatch but they will probably at least partially block the sensor so you would…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Availability of Custom Wiring Harness for 2026 Subaru Forester

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching