Should I Use Metal Screws or Pop Rivets to Install a Vent on a Metal Trailer?

Question

Question:

When installing wall vents or roof vents to the metal skin of the trailer is it better to use pop rivets or sheet metal screws?

asked by: Christopher S

0

Expert Reply:

Hey Chris. It's better to use screws when installing vents like the 2-Piece Exterior Wall Vent for Enclosed Trailers item # HMAV2-AVT2 you were looking at. They're easier to install and remove. They're also better for expansion and contraction from temperature changes.

We have the Camco RV Vent Installation Kit item # CAM25003, which is designed for metal skinned trailers.

What kind of trailer do you have?

expert reply by: Jerred H

0

Exterior Wall Vent
(click to enlarge)

Answer 1

Since heat rises I would at the very least put a set of the Trailer Vents #HMAV2-AVT2 near the top of the trailer to get the hottest air of the trailer out. What you could do for maximum air flow in your trailer is have a set facing forward in the…

view full answer...

Answer 2

One possible solution is the Bauer Products Camper Door Lock - Black #BA65FR. The dimensions you mentioned are very similar to that of the #BA65FR which has required cutout dimensions: 5-1/4" wide x 4-1/2" tall.

view full answer...

Answer 3

Even at an angle I do not think a 28 inch tall tire will fit in toolbox #DZ91717. The box measures 22-3/4 inches tall, 19 inches front to back, 34 inches long at the back and 20-3/4 inches long at the front. Basically I don't think you could get…

view full answer...

Answer 4

When installing a product such as the 2-Piece Polypropylene Trailer Vent for 3" #HMAV2-AVT2 inside the trailer, the best way to face vents to prevent items blowing around the trailer depends on the vent location. There are slots on one side of…

view full answer...

Answer 5

Hey Kevin. The Replacement Door item #DMC58FR is designed to fit the Dometic RV Water Heater item #DMC74FR, which has vents built into the unit itself. This 6-gallon water heater would be a great option to replace a Suburban SW6DEL heater but the…

view full answer...

Answer 6

I actually like your first idea better because we have trailer vents that you can install on your door to help keep water spray away from the internal components. Our selection ranges from battery box vents like part #A10-3300BK-05 to ventilator like…

view full answer...

Answer 7

You can install the 2-Piece Polypropylene Trailer Vent for 3" Diameter Hole - Black #HMAV2-AVT2 in whatever manner suits you best; some people install it so the half-moon is facing to the rear though most do it with the half-moon facing down. I…

view full answer...

Answer 8

The Dexter Axle Torflex axles are basically broken up into the following categories: #9 - 1,000 - 2,200 lb #10 - 2,300 - 4,000 lb #11 - 4,100 - 6,000 lb #12 - 5,500 - 7,200 lb Based off of your 2004 R-Vision Trail-Lite Model 8306S being a tandem axle…

view full answer...

Answer 9

Hi Chuck! The MORryde RV Cargo Slide Tray - 72" x 26" - 1 Way Slide - 60 Percent Extension - 800 lbs #MR67FR sits 1.6 inches above the floor you mount it on. If you want or need it to be a bit higher off the floor, you can also grab the…

view full answer...

Answer 10

Hey Michael, welcome back! While we don't have any installation videos on the Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel item #PD4655V we do have one on the 45 amp item #PD4645V that I have attached below.…

view full answer...

Answer 11

Most of the RV roof vents we have available, such as the Ventline Ventadome Trailer Roof Vent - Metal #V2110SP-24, can be adjusted a bit based on the roof thickness. This particular vent includes a garnish that is designed to fit roofs from 1-7/8…

view full answer...

Should I Use Metal Screws or Pop Rivets to Install a Vent on a Metal Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching