How Tall is the Bulldog Zinc Top Wind A-Frame Jack BD1750290301 From the A-Frame Bracket?
Updated 09/30/2025 | Published 09/05/2025
Products Featured in This Question
Question:
I am looking for a jack for my horse trailer with a shorter distance from the mounting plate to the top of the jack so that the tailgate of my Rivian R1T will not hit the jack. I already have an extended hitch but the tailgate will still hit the jack that I have. I am looking at the Bulldog Zinc top wind A-frame 5,000 lb jack. The specs say that the clearance from the mounting plate to the top of the jack is 10 11/16. Does this include the crank. If it does it should work for me. The existing jack has that clearance at over 13
asked by: Debby L
Expert Reply:
Hey Debby. The 10-11/16" measurement does not include the handle and how it attaches to the Bulldog Zinc Top Wind A-Frame Jack item # BD1750290301. That's only to the top of the jack portion itself from the a-frame mounting bracket. With the handle included it's right at 12" tall from where the bracket bolts to your trailer.
How far is it exactly from the a-frame coupler on your trailer to your tailgate when it's down? Is that the 13 you mentioned at the end of your question?
Product Page this Question was Asked From
Bulldog Zinc Top Wind A-Frame Jack - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jacks
- Standard Grade
- 4001 - 5000 lbs
- Manual Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: trailer jack
- Video: A Closer Look at the Bulldog Detachable Footplate
- Video: Bulldog Top Wind A-Frame Jack Review
- Video: A Closer Look at the Bulldog Round, A-Frame Jack Drop Leg and Pull Pin Assembly
- Video: A Closer Look at the Ultimate Trailer Jack
- Video: Review of Bulldog Trailer Jack - Detachable Footplate - BD500244
- Video: Bulldog Trailer Jack - A-Frame Jack - BD1750290301 Review
- Search Results: bulldog trailer jack
- Shop: Trailer Valet Adjustable Drill Powered Square Jack - 3,000 lbs
- Shop: Bulldog Zinc Top Wind A-Frame Jack - 5,000 lbs
- Shop: Bulldog Round, A-Frame Jack - Topwind - 15" Lift - Zinc - 2,000 lbs
- Shop: Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs
- Shop: Bulldog Detachable Footplate with Pin for 2" Jack Tube - 2-1/10" Tall
- Shop: Replacement Square Footplate for Bulldog Round Trailer Jacks w/2" Diameter Tubes - 2" Tall
- Shop: Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate - Sidewind - Side Mount - 1.8K
- Article: Holiday 2025 | Staff Picks for Real-Life Adventures
- Q&A: Can Bulldog Powered Drive Trailer Jack Be Installed SIdeways for Tailgate Clearance
- Q&A: Can I Take the Inners from Your etrailer 7K Jack and Put them in My Bulldog 5k Jack Welded to Frame?
- Q&A: Recommended Replacement for 7.50-15LT Trailer Tire
- Article: Trailer Wiring Diagrams
- Q&A: Installation Of Square Drop Leg A-Frame Jack On Coupler With Round Hole
- Q&A: Mounting Bolt Hole Pattern of Bulldog 195318 Drop Leg 3000lb A-frame Jack
- Q&A: Bulldog A-Frame Trailer Jack with Hole for Footplate or Caster Wheel
- Q&A: Will The Demco A-Frame Trailer Coupler DM14793-81 Replace The CA-5210-B Coupler?
- Article: How to Tell the Weight Rating of a Trailer Axle
Jerred H.
9/29/2025
Hey Debby, did you find that the Bulldog Zinc Top Wind A-Frame Jack worked for your Rivian R1T and horse trailer setup? I'm asking because your experience could really help others in a similar situation.