What Is The Overall Height Of The Curt Pop-In Ball C60601?

Question

Question:

I need to know the entire height of the ball. I need the overall height for eh gooseneck ball to be less than 7 7/8 inches. 6 3/4 would be optimal

asked by: Jay L

0

Expert Reply:

Hello Jay, thanks for reaching out. The Curt Pop-In Ball # C60601 is 6-13/16" tall overall. I have included a picture with some dimensions for your reference.

Why are you needing the ball to be a specific height? Just curious.

expert reply by: Jesse M

0

C60601 Dimensions
(click to enlarge)

Jay L.

8/7/2025

I am needing to lower the front of my 5th wheel. My bed rail to trailer gap is about 9” and would like to get it to 7”. King pin is adjusted all the way up.

Jesse M.

8/8/2025

@JayL Ok that makes sense. That Curt ball looks to be the shortest we offer and it sounds like it will work for you. Aside from that, the only other solution for this would be to add a lift kit to the 5th wheel which would be WAY more involved so hopefully the Curt ball gets you where you need to be. Come find me if you ever need anything else!

Answer 1

Hey Joshua, thanks for reaching out. That specific offset adapter is not offered as a replacement part. We carry the Convert-A-Ball adapter set #CAB-C5GX1216, but the offset portion is not available on its own. You may want to contact the…

view full answer...

Answer 2

I can help you navigate those tight turns in your 2014 Ram 2500. Since the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter #CAB-C5GX1216 that you referenced does not move the pivot point further back you really do not gain much clearance for…

view full answer...

Answer 3

Actually to install the Convert A Ball Adapter part #CAB-C5GX1216 on your trailer you don't have to drill any holes in the pin box plate. Convert-A-Ball states that they guarantee that the adapter will stay in place without drilling holes, but if…

view full answer...

Answer 4

Hi Mike; I noticed you were looking at a B&W 5th wheel hitch. Is your gooseneck hitch the B&W Turnoverball? The hole for the ball would be square if it is. If so, you can use the B&W Companion #BWRVK3400-5W. However, this is a heavy…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Is The Overall Height Of The Curt Pop-In Ball C60601?

Product Page this Question was Asked From

Continue Researching