Is The Yakima OutPost HD Ladder Rack Compatible With An EGR Electric Retractable Tonneau cover
Updated 11/03/2025 | Published 01/10/2025
Question:
Will this yakima rack work with an EGR electric tonneau cover?
asked by: Clint
Expert Reply:
Hey Clint,
I was waiting on a reply back from EGR if they've tested this but it's been a week with no response from the rep I was talking to. Most likely you could make the Yakima OutPost HD Overland Truck Bed Rack w/ Tonneau Cover Adapters # Y01152-5855 work since it's just using square nuts to mount to the t-slot, but I'm not able to confirm if the adapter plate # Y01155 is going to match up with the design of the EGR rails. The adapter curves down to sit against the rails so depending on how far the slot is from the edge of the rails the adapter might not fit.
I took some pictures of the adapter to show this and measured from the edge of the adapter to the center of the mounting holes to find the spacing was 2". The side lip that comes down on the adapter to sit against the rails eats into about an 1" of those 2" inches so you would need check your cover's slot to edge spacing to see if this might work.
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Yakima OutPost HD Overland Truck Bed Rack w/ Tonneau Cover Adapters - 68" Crossbars
- Ladder Racks
- Truck Bed
- Fixed Rack
- Crossbar Rack
- Tonneau Compatible
- Mid-Cab Height
- 300 lbs
- Over the Bed
- No Drilling Required
- Yakima
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: adjustable coupler
- Search Results: trailer hitch cover
- Search Results: trailer jack
- Search Results: electric jack
- Search Results: boat trailer winch strap
- Search Results: boat trailer parts
- Search Results: gorilla lift
- Shop: Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable - 300 lbs
- Shop: ABS Black Hasp Assembly for Latch Systems
- Shop: Pollak Circuit Breaker - Cycling/Automatic Reset - 30 Amp - Straight Mount Bracket
- Shop: CargoBuckle Ratcheting Tie-Down Strap - 2" x 15' - 833 lbs - Qty 1
- Shop: Derale Automatic Resetting Circuit Breaker - 50 Amp
- Shop: CargoBuckle Mini G3 Retractable Ratchet Straps - 1" x 6' - 466 lbs - Qty 2
- Shop: Back the Blue Thin Blue Line Flag Trailer Hitch Cover - 2" Hitches - Stainless Steel
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Measuring To Choose The Right Trailer Axle
- Q&A: What Sealant Should I Use Between an Aluminum Jeep-Style Fender and My Trailer?
- Article: Trailer Lighting Requirements
- Shop: Trailer Wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Bigfoot Hydraulic Jack DIY Installation - Diamond C Trailer
on Ladder Racks
Jesse M.
11/3/2025
Hey Clint, were you able to check the slot-to-edge spacing on your EGR cover to see if the Yakima OutPost HD rack would line up? Knowing how that measurement worked out could help others trying to pair the same setup.