Installing Timbren Front Jounce Bumpers On A 1995 Ford Bronco With Riveted Factory Jounce Bumpers
Updated 01/15/2025 | Published 01/06/2025 >
Question:
1995 Ford Bronco front Timbrens. I ordered these a while ago and tried the install this weekend. The stock bumper is attached to the shock tower bracket see from rear.... that is riveted to the frame. The bumper looks fused somehow to the plate - there is no obvious bolt that holds it in place. There doesnt appear to be any way to remove the bumper without drilling out multiple rivets from the plate and removing the plate which may compromise the frame, or maybe an air/cold chisel to shear it off. This is definitely not a unbolt-the-old, bolt-in-the new and appears to require major work just to get the old bumper off and drilling a new hole in the frame - if the rivet is the other hole position - see from front. See the attached pictures. Can you provide additional install information, the instruction sheet is useless. Thnx, Byrl
asked by: Byrl T
Expert Reply:
Hi Byrl,
The stock jounce bumper should have a bolts running up into the frame just like the Timbren # TFF1504H does, but if you're saying that they were instead riveted to the frame the only option would be to drill out the rivets to get them removed. This is definitely a tough one because there's very limited space to work. Would you be able to get a picture of the rivets possibly?
Product Page this Question was Asked From
Timbren Front Suspension Enhancement System
- Vehicle Suspension
- Towing/Load Leveling
- Bump Stops
- Suspension Only
- Light Duty
- Front Axle Suspension Enhancement
- Timbren
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Lift Kit Solution to Allow Fifth Wheel Trailer to Sit More Level When Towed
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch





Byrl T.
1/10/2025
Hi Kevin, the rivets are the smooth hemispherical nubs in the pictures. I suppose I could use a grinder to cutoff the head on one side and try and punch it through the frame and replace with a bolt, but if it doesn't work it would be nearly impossible to drill out. And I don't know if the hole spacing would match up with the new plates since I can't tell how the rubber snubber is attached. Actually, the pictures I sent have the labels wrong - the first picture (1) is from the front of the vehicle looking towards the back, and the next two pictures (2, 3) are from the rear of the vehicle looking towards the front. So would probably need to remove the rivet nearest the snubber in picture 1. But then the plate for the new Timbren would be spanning the thicker metal where the rivet is located. Doesn't seem right, or that the Timbrens are designed for this vehicle application. I could take some more pictures of the rubber snubber but there is no obvious way it is attached to the metal. I can't tell if it's molded to the metal plate or what. There is a cutout in the frame where I can see the backside/top of the area where the snubber is mounted. There is a hole in the frame and what appears to be a rubber extrusion - it doesn't appear to be a bolt head. I have little faith that the hole spacing between it and the rivet would match up with the hole spacing in the Timbren mounting plate.