Replacement Male & Female MC4 Connectors For A Solar Panel Entry Plate
Updated 11/17/2025 | Published 12/30/2024
Products Featured in This Question
Question:
I have a go power solar entry cable plate mounted on the roof of my RV. I want to replace the male and female connectors that are fixed on the mount. Part?
asked by: Keith
Expert Reply:
Hey Keith.
The male and female MC4 connectors on your entry plate # 34273840 can be replaced with part # RED98VR. You'll need to unscrew the cap to on the connector to loosen it from the wire and can then pull the housing off. The metal prong that crimps onto the wire and locks into plastic housing is going to fight you so I'd pull on the housing with some pliers to make it easier. Just be careful you aren't pulling to hard and accidentally hit something else.
Once replaced I'd also check your the entry plate as well as the other accessories on your RV's roof to see if they need another coating of sealant # 34427034145-1. If so you'll want to wipe down the old sealant with some alcohol, let it dry, and then reapply the sealant right over the old sealant.
Product Page this Question was Asked From
Go Power Solar Cable Entry Plate for MC4 Cables
- Accessories and Parts
- RV Solar Panels
- Cables and Connectors
- Cable Entry Plate
- Go Power
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: decor sealant
- Search Results: decor self leveling
- Search Results: lubricants sealants adhesives
- Shop: Go Power Solar Cable Entry Plate for MC4 Cables
- Shop: Redarc MC4 Connector Kit for Solar Panels
- Video: Redarc MC4 Connector Kit for Solar Panels Spec Review
- Search Results: go power
- Search Results: lippert jack
- Search Results: lippert
- Search Results: camper jacks
- Shop: etrailer MC4 Expansion Branches - Qty 2
- Shop: Rock River Silicone Sealant - 9.8 Fl-Oz - White
- Video: Checking Out the Rock River Silicone Sealant
- Video: Hands-On with the etrailer Solar Panel MC4 Expansion Branches
- Video: Let’s Check Out the etrailer MC4 Expansion Branches
- Q&A: Trailer Valet JXC Trailer A-Frame Jack For 2018 Nucamp Tab400 Travel Trailer
- Shop: MC4 Expansion Branch for Go Power Solar Panels - 3 Male and 1 Female
- Q&A: Replacement Nut Parts for Connecting MC4 Cables
- Shop: Rich Solar MC4 Y-Branch Parallel Adapters for Solar Panels
- Shop: etrailer Sidewind Trailer Jack w/ Drill Adapter - A-Frame - 14" Lift - 2,000 lbs
- Video: Trailer Valet JXC Trailer Jack with Footplate Review | Smooth, Stable Lifting
- Video: Lippert Quick Drop Tongue Jack Manufacturer Review
- Video: A Closer Look at the Lippert Quick Drop Tongue Jack with Topwind and Drive Nut
- Q&A: Can Dexter EZ Flex Equalizer be Used with MORryde X-Factor Crossmember
- Q&A: Which Hangers Should MORryde X-Factor Crossmembers Install On
- Q&A: MORryde X-Factor Crossmember for 2024 Grand Design Reflection 150 Series 295RL
- Q&A: If Using Two MORryde X-Factors on Tandem Axle Which Hangers to Use
- Q&A: How Many MORryde X-Factor Crossmember Supports Are Needed For A Tandem Axle Trailer?
Jameson C.
11/17/2025
Hey Keith, how did the replacement go with the new MC4 connectors on your Go Power solar entry plate? Did the connectors fit securely once you loosened the old ones and crimped the new set in place? Your results could help others working on similar RV roof setups.