Replacement Hub for 1994 Triton Lite Snowmobile Trailer with L44649 Bearings

Question

Question:

I have a 94’ Triton Lite 10 snowmobile trailer. Has 8” tires, hub pattern is 5 on 4.5, easy grease axle, bearing size for inner/outer is L44649. I’m looking for a pregreased hub to replace the current ones. Any help would be appreciated

asked by: Mike K

0

Expert Reply:

Hey Mike!

Sounds like you're needing the Easy Grease Trailer Idler Hub Assembly for 2K Axles # AKIHUB-545-2-EZ-2K.

If you're wanting something with a better protective coating the Galvanized Hub # AKIHUB-545-2-G-EZ-2K will do the trick, but this doesn't come pre-greased so you'll need to take care of that on your end.

expert reply by: Jon G

0

Answer 1

Standard 4-pole trailer wiring uses flat-style connectors, like part #W787268 which is a trailer-side connector and part #HM48044 which is the mating vehicle side connector. On these items and on the 16-gauge bonded 4-pole wire #16-4B-1 you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Replacement Hub for 1994 Triton Lite Snowmobile Trailer with L44649 Bearings

Product Page this Question was Asked From

Continue Researching