Can Self-Contained Hydraulic Jack e33VV be Welded on

Question

Question:

Self-Contained Hydraulic Jack - Square Tube - Bolt On - 12,000 lbs Part Number: e33VV Can I weld my own mounting plate onto this product. the one on it is too small.

asked by: David F

0

Expert Reply:

Hi David,

Yep, if you'd like you can absolutely weld on the 12,000 lb Self-Contained Hydraulic Jack # e33VV.

I have added a cutout from the instructions (linked below) which offer the details on welding this jack.

expert reply by: Kyle S

0

Weld Instructions For e33VV
(click to enlarge)

e33VV Instruction Cutout
(click to enlarge)

David F.

10/14/2024

The Manual says use Dexron Transmission Fluid, The only ATF/Dexron I can get around here is Dexron IV, V or VI or DEXRON VI Synthetic. Which one do you Recomend Or does it Matter. Cant get the Dexron II anywhere around here. Thanks DAVID FUSSELL

Reply

Kyle S.

10/14/2024

@DavidF Any of the ones you mentioned will be perfectly fine to use.

Reply

Answer 1

Hey Dallas, the distance from the mounting bracket of the Dexter Jack #DX72CR out to the furthest point out opposite on the pump enclosure measures 10.4 inches. Please enjoy my crude dimensional drawing and let me know if you have any other…

view full answer...

Answer 2

Hi Nick; the Dexter Self-Contained Hydraulic Jack #DX72CR can be bolted onto your dump trailer. The only other thing you will need is a 12V battery to power the jack. This has a lift capacity of 10,000 lbs, a support capacity of 12,000 lbs, and comes…

view full answer...

Answer 3

Hello Josh. Yes, the Dexter Self-Contained Hydraulic Jack #DX72CR can indeed be welded on. It is intended to be bolted on, but the instructions also cover weld on applications as well.

view full answer...

Answer 4

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 5

Hello Jeff, thanks for reaching out. It is possible to use two of the Dexter Self-Contained Hydraulic Jacks #DX72CR on the same trailer, but there is no way to have both jacks run off the same remote. You would have to have two remotes and use both…

view full answer...

Answer 6

Hi Sean; we only sell replacement parts for this setup at this time so we do not have every part you need. We have the leg #e93VV and the Replacement Power Unit for etrailer and Ram Hydraulic Trailer Jacks and Scissor Hoist Systems #e43VV. The…

view full answer...

Answer 7

Hey Michael. As of right now we do not have a hydraulic jack that can tie into your hydraulic system (Though there have been talks around the building of this possibility), nor the add on to convert a manual to hydraulic, but we do have the #e33VV…

view full answer...

Answer 8

Hey Arthur; the Vesper Steel Modular Trailer Wheel #TA67RR has a standard 0.453" valve stem hole. The valve stem is included with the wheel. If you're planning to replace the valve stem with one that can handle a high psi rating you can use…

view full answer...

Answer 9

Hey Bill, thanks for getting in touch. The Dexter Self-Contained Hydraulic Jack #DX72CR is powered by the trailer battery. Dexter recommends a full size deep cycle RV/marine battery.

view full answer...

Answer 10

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Can Self-Contained Hydraulic Jack e33VV be Welded on

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching