Replacement Suspension Components For A 2021 CrossRoads Sunset Trail Super Lite SS289QB
Updated 01/27/2026 | Published 08/15/2024
Products Featured in This Question
Question:
I have a Crossroads Sunset Trail 289qb with a bent axle. I am looking for a factory replacement along with hub seals, and u bolts. I am also interested in upgrading the hardware for both axles with upgraded equalizers for in between the springs.
asked by: Eric H
Expert Reply:
Hi Eric,
To replace each of these components you'll first need to take some measurements. For the axle you'll need to remove a wheel on each side and measure from the face of the hub on one side over to the face on the other side of the axle. I would jack up the back by the frame to get the two rear wheels off. Next you'll need to measure the spring seats from center to center.
For the bearings and seals you can check them to see if their part numbers are still stamped into them. If the part numbers have faded/worn away then you can measure the spindle at points B, C, and D with a caliper # PTW80157 for their inner diameters. For outer diameter you can measure the bore hole of the hub. With these measurements I can look up what the bearings and grease seals are.
If you want to replace the leaf springs you'll want to remove a wheel and lift the trailer by the frame to take the weight of the leaf springs and can then measure from center to center of the eyelets. You would also do this with the shackle straps and the equalizer. With the equalizer you'll also measure vertically from the hanger eyelet down to the center of the shackle strap eyelets (see diagrams below).
For the bolts you'll just need to measure how thick they are (likely 9/16") and how long they are overall/length of the shaft under the head. If you want wet bolts so that you can apply grease just let me know. Otherwise I can pick out some standard bolts with nylon bushings so that you don't have to do any maintenance.
Let me know what you find and I'd be happy to pick out the right components.
(click to enlarge)
(click to enlarge)
(click to enlarge)
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Dexter Trailer Axle Beam with Standard Spindles - 89" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 3500 lbs
- Spindles Only
- 74 Inch Spring Center
- 89 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Q&A: Replacement 2,500 lbs - 3,500 lbs Axle w/a 86.5" Hub Face and a 68.5" Spring Center
- Q&A: What mounting hardware would I need to install CE Smith Single Axle Trailer Fenders?
- Article: Most Popular Wheel Bearings
- Q&A: Correct Round U-Bolts for 3,500 Lb Dexter Trailer Axle
- Q&A: Can Straight and Cambered Axle be Used on Tandem Axle Trailer
- Q&A: What Does 5 on 5 And 5 on 4-1/2 Mean For Trailer Wheels
- Q&A: How to Measure Trailer Leaf Spring to Find Correct Replacement
- Q&A: Dimensions of Spindle on 3,500 Pound Dexter Trailer Axle
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: How to Measure a Trailer Axle
- Article: How to Raise Your Travel Trailer Height
- Article: Trailer Wiring Diagrams
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Trailer Brakes Not Working? Troubleshooting Guide
Gwendolyn Y.
1/27/2026
Hey Eric, were you able to get those axle and suspension measurements for your Sunset Trail? Once you have them, I can help match the right replacement parts. Let me know what you find—I’m here if you need a hand narrowing it down.