Outer Diameter of Replacement Spindle Washer for Dexter Nev-R-Lube Hub and Drum

Question

Question:

What is the OD of this washer?

asked by: Roger W

0

Expert Reply:

Hey Roger,

The outside diameter is 2-7/16 inches for the Replacement Spindle Washer for Dexter Nev-R-Lube Hub and Drum Assemblies # 5-149.

expert reply by: Kyle S

0

Diameter of Spindle Washer # 5-149
(click to enlarge)

Answer 1

From what I was able to determine from my research, the 023-326-00 brakes are 12" brakes from Dexter and were designed for trailer axles with between 5200 and 7000-lbs capacity. I don't believe that I've ever seen a brake mounting flange…

view full answer...

Answer 2

You do not need to replace the Spindle Nut #6-183 for your Nev-R-Lube axles every time that you remove the hub. The only time you need to replace it is when it isn't functional anymore. I reached out to my contact at Dexter Axle who confirmed…

view full answer...

Answer 3

According to Dexter Axle, the attachment bolts for a 12 x 2 brake assembly should be torqued to 25-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 4

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 5

The right and left orientation is determined if you are standing behind the trailer looking towards the tow vehicle. The left side is the drivers side and the right side is the passengers side. Tthe shorter brake pad will always be in the front of…

view full answer...

Answer 6

Hey Corey, If you are not liking the brakes you have on your trailer and want to remove them and go with idler hubs you definitely can, if your trailer is lightweight enough. I am not sure what your state laws are, or states you travel but some…

view full answer...

Answer 7

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 8

The part number you gave is no longer a valid number for Bulldog jacks. It sounds like you are looking for the Bulldog Square Jack w/ Footplate - Drop Leg - Sidewind - 15" Lift - 5,000 lbs #BD190754. This has a 5,000 lb lift capacity and an…

view full answer...

Answer 9

I'm not sure why they said those were your only options, but we do have the correct replacement oil seal for your Dexter 10k hub from 2006, and is the exact replacement for a National 370150BG: - Unitized Oil Seal #10-51 The #10-51 has an inner…

view full answer...

Answer 10

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 11

It is acceptable and highly water insoluble so it is great for boat trailers. Grease like the LubriMatic LMX Industrial Strength Grease #L11390 is a lithium complex. The same is true for Lucas Red N Tacky which means they are compatible.

view full answer...

Outer Diameter of Replacement Spindle Washer for Dexter Nev-R-Lube Hub and Drum

Product Page this Question was Asked From

Continue Researching