Are #84 Spindles Threaded into the Axle?

Question

Question:

Are the spindles threaded into the axle? I just assumed they were welded.

asked by: Jay

0

Expert Reply:

No, they're welded. You assumed correctly. The spindles listed below that I referenced in your previous question all have to be welded on. There are no thread on spindles.

#84 Spindle for 3,500-lb Trailer Axles - 2" Diameter item # TRU24FR

#84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter item # TRU84FR

Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide item # TRU47FR

expert reply by: Jerred H

0

Answer 1

If you check out the diagram I attached you'll see how the O-ring of the Bearing Buddy Grease Seal set part #BB60002 installs. It's location is designed to compress between the seal ring and grease seal to help prevent the seal from leaking…

view full answer...

Answer 2

I have three spindles that are for a 3,500-lb axle and have the bearing dimensions you have listed. The only difference is the dimension for the grease seal is 1.75 inches, not the 1.795 inches that you have mentioned. Maybe you typed in the seal…

view full answer...

Answer 3

We carry the Bearing Buddy Spindle Grease Seal Set #BB60002 instead of the Dexter sleeve. I do not recommend the Dexter as with the one hole if that sleeve were to spin on the shaft it would block the hole of the EZ lube grease zerk. With the Bearing…

view full answer...

Answer 4

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 5

The #84 E-Z Lube Spindle #TRU74FR matches the dimensions of the #84 Spindle #TRU64FR and will have the E-Z lube spindle and a brake flange. With the brake flange the stub will be 3/4" longer. If necessary you can cut off the brake flange to get…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Are #84 Spindles Threaded into the Axle?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching