Are Backing Plates Alone Sold For Brophy Swiveling D-Rings

Question

Question:

Please let me know if you sell the backing rings alone for the Brophy swivel D-rings. I already bought the D-rings from you before the backers were available. Regards

asked by: Charles F

0

Expert Reply:

Yes, for the Brophy Swiveling D-Ring Tie Down Anchor # RR06 there are backing plates available by themselves, with the correct part being the following:

- Backing Plate for RR06 Recessed Swivel D-Ring Tie Down # BP06

expert reply by: Kyle S

0

Answer 1

I pulled the Brophy Trailer D-Ring Tie Down, #RR06, from my warehouse to measure and verified that the diameter of the flange is in fact 6-5/16 inches. I also verified that all other measurements on the product page are correct. I have attached the…

view full answer...

Answer 2

The Brophy Swiveling D-Ring Tie Down Anchor part #RR06 does not come with a backer plate and it's not typically used with one. The backer plate is not required but if you wish to use one you'll need to construct this on your own.

view full answer...

Answer 3

There is no difference between the D-Ring Tie Down, part #RR06 and the tie-down that is included in the #RR6K other than the backing plate and the mounting hardware. the D-Ring is the same for both of these items. These have a capacity of 6,000 lbs…

view full answer...

Answer 4

I pulled a trailer D-Ring from our warehouse and took a measurement for you. the depth of the D-Ring housing from the bottom of the flange with the mounting holes is 7/8 inches. The 1/4 inch mounting holes are spaced 3-3/16 inches apart. The mounting…

view full answer...

Answer 5

The Brophy Swiveling D-Ring Tie Down Anchor part #RR06 with the Backing Plate for RR06 Recessed Swivel D-Ring Tie Down part #BP06 are a great, easy to install set of tie-downs which can be used for securing a vehicle. The tie-downs themselves have a…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Are Backing Plates Alone Sold For Brophy Swiveling D-Rings

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching