Washer And Bolt Size Needed For The JR Products Rubber Bumper for Enclosed Trailer Ramp Door

Question

Question:

Re: 2.5D rubber bumper for enclosed trailer ramp door. What size washer and bolt to these take?

asked by: Jan K

0

Expert Reply:

The Rubber Bumper for Enclosed Trailer Ramp Door # 37210715 can fit a washer with a 1" outer diameter and 3/8" inner diameter. The bolt can be anything 3/8" in diameter or smaller and the length is going to depend on how thick of a ramp door you're attaching it to.

expert reply by: Kevin C

0

Answer 1

We have a couple of options for rubber bumpers but neither one of them has a 1/4" mounting hole. You can use a washer and install the Rubber Bumper for Enclosed Trailer Ramp Door item #37210715 you were looking at. The other option is the…

view full answer...

Answer 2

I checked your order notes and the part number you ordered was 385800 which is no longer available but the part #37210715 is essentially the same thing so it would work just as well if not better.

view full answer...

Answer 3

The hole diameter of the Rubber Bumper for Enclosed Trailer Ramp Door #37210715 is 3/8 inch so you'd want to pick a screw or bolt with that diameter to fit the best. We have a 3/8 inch diameter lag bolt with part #FA74521 which might work for…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Washer And Bolt Size Needed For The JR Products Rubber Bumper for Enclosed Trailer Ramp Door

Product Page this Question was Asked From

Continue Researching