Gen-Y Gooseneck To Pin Box Replacement For A Lippert Turning Point Pin Box

Question

Question:

I would like to replace my Lippert 722704 5’th wheel pin box with a gooseneck pin box but I’m not sure which one to get. Any help is appreciated.

asked by: Gabriel A

0

Expert Reply:

To replace your Lippert Turning Point with a Gen-Y gooseneck pin box you'll need to match the bolt pattern and pin weight of your 5th wheel trailer. The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert Turning Point - 21K - 3.5K TW # GY48GR you were already looking at has a matching bolt pattern and pin weight range of 1,500lbs to 3,500lbs. You'll just want to look at the sticker on the driver's side of your trailer that lists the pin weight and GVWR of the trailer to confirm that this will be a compatible match.

expert reply by: Kevin C

0

Lippert Turning Point
(click to enlarge)

Lippert Turning Point 2
(click to enlarge)

Answer 1

The part number you listed is a Coleman Mach AC unit so that means that the replacement shroud part #MA00-325001 would be the correct shroud replacement.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Gen-Y Gooseneck To Pin Box Replacement For A Lippert Turning Point Pin Box

Product Page this Question was Asked From

Continue Researching