Will The Reese Weight Distribution Shank Fit With Blue Ox Sway Pro Weight Distribution Hitch?

Question

Question:

Can RP54970 be used with the Blue Ox Sway Pro?

asked by: Gregory W

0

Expert Reply:

While the holes are still spaced 1-1/4" apart for the Reese Weight Dist Shank # RP54970 I do recommend staying with the Blue Ox Shank # BXW4001 The Blue Ox uses a solid shank unlike the Reese which has ears that are not as strong.

expert reply by: Bud M

0

Answer 1

The correct replacement glass top solution for your black FGR21G3A2-BG would be the part #FR46NR.

view full answer...

Answer 2

Hi Steve; a pin box with the Lippert Rhino bolt pattern will not fit the 1621 bolt pattern. You have to match the bolt pattern on your 5th wheel when choosing a replacement. Were you wanting to get the Rota-Flex you were looking at? Assuming you are…

view full answer...

Answer 3

The Solera 12V Power RV Awning Conversion Kit #LC434724 that you referenced would work great as a replacement for the Carefree Fiesta manual arms you have now. This will make extending and retracting your awning much easier. I attached a review video…

view full answer...

Answer 4

Yes. If you don't need the weight distribution bars attached to carry the trailer to storage, you can absolutely use just the WD hitch head and ball to tow the trailer. It will work just like a ball mount.

view full answer...

Answer 5

It looks like you have a pretty good plan, but I recommend one change. I recommend using the Blue Ox SwayPro Weight Distribution Shank for 2" Hitches - 12" Long - 7 Hole Adjustment #BXW4001 with the Curt MV Weight Distribution System w/…

view full answer...

Answer 6

Hey Donald, Are you just wanting to replace the rooftop unit or the entire system? If you're wanting to replace just the rooftop unit then we'll need to first identify your specific unit since Dometic systems don't play nice with others.…

view full answer...

Answer 7

Hey Brad, The wire torsion spring you're needing for your B&W Patriot 5th Wheel Trailer Hitch #BWRVK3255 can be picked up directly from B&W. IF you give them a call they'll be more than happy to ship you one.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Will The Reese Weight Distribution Shank Fit With Blue Ox Sway Pro Weight Distribution Hitch?

Products Featured in This Question

Continue Researching