Does eZ-Latch Demco Channel Tongue Trailer Coupler Fit a 3x3 or 2x3 Tube

Question

Question:

Does this fit on a 3x3 tube or a 2x3 tube?

asked by: Tim

1

Helpful Expert Reply:

The Demco Channel Tongue Trailer Coupler - eZ-Latch # DM15945 is designed for a 3"x3" tube.

expert reply by: Jon G

1

Answer 1

I recommend using the Fulton Fold-Away Coupler Hinge Kit for 3" x 3" Trailer Tongue - Weld On - Up to 5,000 lbs #FHDPW330300 which will allow you to cut your tongue and add a new 3" x 3" piece with the coupler to get the extra…

view full answer...

Answer 2

The Fulton Fold-Away Coupler Hinge Kit #FHDPB230101 is for a trailer tongue 2" wide by 3" tall. having a trailer tongue which is wider than it is tall is very strange. You can use the Fulton Fold-Away Coupler Hinge Kit #FHDPW330300 but will…

view full answer...

Answer 3

We do have a fold away coupler that will work on your trailer tongue that is 2 inches by 3 inches and that is the Fulton #FHDPB230101. This coupler will install on your trailer tongue and has a cacity of up to 5,000 pounds. Please note that the…

view full answer...

Answer 4

I recommend using the Fulton Fold-Away Coupler Hinge kit part #FHDPB230101 that fits a 2"x3" trailer tongue. It comes with all the hardware needed to install. Please keep in mind the trailer tongue material thickness must be…

view full answer...

Answer 5

I was able to find the tire size on a 2017 model is ST205/75R14C and the bolt pattern is 5 on 4-1/2 inches. So for your spare, you will want the Castle Rock ST205/75R14 Radial Tire w/ 14" Condor Aluminum Wheel - 5 on 4-1/2 - LR C - Gunmetal…

view full answer...

Answer 6

The latch of the Demco Channel Tongue Trailer Coupler #DM15945 that you referenced is pre-adjusted to fit a 2 inch ball as-is and would not require you to do any initial adjustments for it to work properly.

view full answer...

Answer 7

The bolt holes on the Demco coupler #DM15945 are 3" apart on center. I have included a drawing below that shows the dimensions. You can use a 1/2" grade 5 or higher bolt to attach to the tongue of your trailer.

view full answer...

Answer 8

On the Demco coupler part #DM15945 the upper mounting holes are separated by 3 inches and the lower hole is right in the middle of those two at 1-1/2 inches from left to right. The rear hole is 1 inch from the back of the coupler. This is a dimension…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Does eZ-Latch Demco Channel Tongue Trailer Coupler Fit a 3x3 or 2x3 Tube

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching