Phone Will Not Pair Echo With Bluetooth Settings

Question

Question:

Removed the echo wireless brake controller from previous tow vehicle, had it installed on new tow vehicle but now it will not pair with my cell phone. The flashing blue light when trailer not connected or green light when trailer is connected work but the controller can’t find my cell phone to connect. It worked with no problems on the previous vehicle. I removed the app and reinstalled it, I d the pairing on my Bluetooth settings from before. Still no connection. Any other ideas?

asked by: Greg M

0

Expert Reply:

Thank you for your purchase directly from etrailer of the Curt Echo Wireless Brake Controller # C51180. I can take a guess at the issue, and based on my understanding of what you wrote, the problem could be with the pairing on the Bluetooth settings from before. Try going into your settings on your phone and make sure to disconnect the Bluetooth from the Echo, then go to the Curt app and pair the brake controller. If you do not disconnect the Bluetooth from the Echo in your settings it will not allow you to pair. If this doesn't work you have a warranty claim with Curt.

expert reply by: Kyle S

0

Answer 1

First check to make sure that your iPhone is up to date on its iOS updates. Then check to make sure you have the most up to date version of the Curt Echo App in your app store. You will want to make sure that your Bluetooth connection is on and the…

view full answer...

Answer 2

Hey Desirerme, so the Curt Echo #C51180 did have some initial problems when the switched it over to the OneControl app which was super annoying, but have you tried checking to see if they have a newer version of the app you can download? A lot of…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Phone Will Not Pair Echo With Bluetooth Settings

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching