Will The Kodiak Disc Brake Kit # K2R1058D11E Fit a Dexter 10K General Duty Axle From 2019?

Question

Question:

Will these fit a 2019 dexter 10k General duty axle with 17.5 single wheels.

asked by: Brent

0

Expert Reply:

Yes, the Kodiak Disc Brake Kit # K2R1058D11E will fit your Dexter 10,000LB general duty axle manufactured in 2019.

expert reply by: Bud M

0

Michael H.

11/23/2024

This has been my question as well. This kit says that it is for 16 inch duals or larger but i have single 17.5 wheels, you are saying this kit will work for us with 17.5 singles, correct?

Answer 1

In order to convert a Dexter 10K Axle (Made After May 2013) from electric drum to hydraulic disc brakes you'll need the following: Kodiak Disc Brake Kit part #K2R1058D11E (1 per Axle) Dexter Oil Hub for 9K to 10K General Duty Axles part…

view full answer...

Answer 2

Hello Baltazar. I am happy to look into it and recommend parts for you, but I will need more information from you first. Mainly I need to know what kind of brakes are currently on your trailer. If you have electric brakes you are going to need a full…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Will The Kodiak Disc Brake Kit # K2R1058D11E Fit a Dexter 10K General Duty Axle From 2019?

Continue Researching