Actuator Solution that Can Fit 4 inch Wide Tongue

Question

Question:

Is there an actuator made to fit a 4inch tongue ?

asked by: Jim

0

Expert Reply:

You could weld an actuator like the Dexter Drum Brake Actuator part # T1607500 to the top of your trailer tongue but there isn't one that fits around a 4 inch wide tongue. If your brakes are disc instead you'd want the part # T4749600.

expert reply by: Jameson C

0

Answer 1

The DICO Model 10 that you have is essentially the exact same thing as the Titan Brake Actuator #T1607500 that you referenced. This would be an exact replacement.

view full answer...

Answer 2

For a weld on option, Titan Weld on Brake Actuator part #T1607500 is a good option. The Titan Brake Actuator welds onto a 3" wide trailer tongue and takes a 2-5/16" ball. This actuator does not have a reverse lock out option. WIthout a…

view full answer...

Answer 3

If you check out the picture I attached to this you'll see how one person welded on a Titan Model 10 like the part #T1607700 that you referenced. It really depends on the application though. Either way you'll need to find a qualified welder…

view full answer...

Answer 4

Yes, you will be able to remove the master cylinder from the Titan Brake Actuator - Painted - Drum - 2-5/16" Ball - Weld On - 12,500 lbs, part #T1607500. This is a direct replacement, so you will not need a reducer. The master cylinder you need…

view full answer...

Answer 5

Unfortunately you will have to remove everything in order to properly complete the weld install of the Titan Brake Actuator, Item #T1607500. Please contact me if you have any other questions.

view full answer...

Answer 6

Disc brakes stop harder than drum brakes and require less maintenance. You will need to make sure the brakes all match if you are adding to the second axle. Also you will need to make sure you have the correct actuator. If you have drum brakes on…

view full answer...

Answer 7

I googled the grease seal number you mentioned and I did find some options online but when I looked up the size it wasn't one that we carry a suitable replacement for. For a coupler solution though you could use the Dexter part #T1607500 which…

view full answer...

Answer 8

Thanks for the photos of your trailer's actuator! They were very helpful in answering your questions. Based on the photos, it appears that you have a Titan Model 10 Actuator #T1607500. For a Model 10 actuator, the #DX66FR that you referenced is…

view full answer...

Answer 9

Atwood Mobile Products was sold several years ago and parts for their braking systems are no longer available, but I do have a solution for you. Your 2006 Dorsey Trailer (23' Chaparral Model) has a GVWR of 7100 pounds. You can replace the surge…

view full answer...

Answer 10

The top width of the Titan Brake Actuator - Painted - Disc - 2-5/16" Ball - Weld On - 12,500 lbs #T4749600 you were looking at measures right at 4" as shown in the included diagram. This will be the exact same dimension as the #T1607500,…

view full answer...

Answer 11

Actuating couplers do not come with a minimum weight capacity, however, there could be some potential issues if you are towing a trailer with a weight well below the capacity of the coupler you are using. For example, I had a situation where a boat…

view full answer...

Answer 12

Almost all trailer brake actuators are designed for 3 inch wide trailer frames, the only option would be to weld a coupler on top of your 3-1/2 inch frame. The issue with this for you is that the options for those only accept a 2-5/16 inch hitch…

view full answer...

Actuator Solution that Can Fit 4 inch Wide Tongue

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching