Determining The Correct Replacement For A Bargman L-100 RV Entry Door Lock

Question

Question:

I have a L-100 bargman lock in a 11/4 inch door width. In a 1966 Overland airstrem Have all the bits apart from a cutoff bolt and wreaked cylinder. Can you help Regards

asked by: Graham P

0

Expert Reply:

I wasn't able to find the cutout dimensions for the Bargman L-100 but since we know the door thickness is 1-1/4" thick we just need to measure the width and height of the cutout hole to find a correct fit. The Global Link RV Entry Door Lock # 295-000019 you were looking at is designed to fit a 1-1/4" to 1-1/2" thick door with a 2-1/2" to 3" wide x 3-1/2" to 4" tall cutout hole.

If you could provide me with these dimensions I'd be happy to find the correct RV entry door lock for you.

expert reply by: Kevin C

0

Chris

5/10/2026

L100 Cutout dim: 2.25 x 2.75. It is smaller than modern standard cutout.

Answer 1

It really comes down to the thickness of the door on your 1967 Airstream. From my research it looks like the 66-68 Airstreams had a thicker door which was over 2-1/4" thick. If you have the thicker door the only option would be to use one of the…

view full answer...

Answer 2

Yes, you can still use the Stromberg Carlson Base Pad Extreme for Campers and Trailers - 6,000lbs - Qty 1 Item #SC88VR. The pad may hang over the sides a little bit but shouldn't interfere with the usage of the base pad.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Determining The Correct Replacement For A Bargman L-100 RV Entry Door Lock

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching