Does Step Wet Bolt Have Torque Setting

Question

Question:

What is the torque specifications on this part?

asked by: Wes

0

Expert Reply:

There is not a specific torque setting for shackle bolts, including the Step Wet Bolt for 1-3/4" Double Eye Springs # 34007-187-00. All you have to do is tighten bolt until the knurled portion of the bolt pulls completely into the shackle strap and the bolt head is ran all the way down to the shackle strap.

expert reply by: Kyle S

0

Answer 1

Hi Hans, We can get your Keystone trailer set up with new leaf springs, bushings, and wet bolts. Thanks for the measurements and let's start with the leaf springs; for 26 inch eye-to-eye springs what you can use is the 4-Leaf Double-Eye Spring…

view full answer...

Answer 2

For the axle U-bolts, we have two different options: - 3" Round Trailer U-Bolts 9/16" Diameter #SP01-080 - 3" Round Trailer U-Bolts - 1/2" diameter #SP01-060 Since these bolts are so close in diameter, I recommend measuring the…

view full answer...

Answer 3

Based on the current condition of your Dexter EZ Flex kit it's going to be the best solution to replace the entire kit with the part #K71-653-00. This comes with the two new equalizers you need, all new shackle straps, new bolts, nuts, and…

view full answer...

Answer 4

If the U-bolts are 9/16 inch diameter, the torque specs should be between 65 to 95 foot lbs. If the U-bolts are 3/8 inch diameter, the torque should be between 30 and 50 foot lbs.

view full answer...

Answer 5

A 9/16" shackle bolt like the Step Wet Bolt for 1-3/4" Double Eye Springs #34007-187-00 actually does not have a recommended torque because tightening the shackle bolts too much will crush the shackle straps up against the leaf springs, and…

view full answer...

Answer 6

You will need the U-Bolt Kit item #APUBR-1 to use the 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 27" Long item #SP-210275. The kit uses 1/2 inch diameter nuts that you will want to torque them down to about 70 foot pounds.

view full answer...

Answer 7

For U-bolts like #APUBR-1 the torque spec is between 45 and 75 ft-lbs. For the shackle bolts on the end of your leaf springs and a standard equalizer there are no listed torque specs. If you make them too tight they won't function properly. I…

view full answer...

Answer 8

Thank you for the photo! I was able to use the serial number on your axle to determine which is the correct replacement leaf spring for your trailer. For this, you are going to want to use the 3-Leaf Double-Eye Spring #e57SR. The measurement you…

view full answer...

Answer 9

According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part #K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.

view full answer...

Answer 10

The flange nuts that come with the Dexter Heavy Duty Suspension Upgrade Kit #K71-358-00 are 7/16 - 20. My contact at Dexter Axle confirmed this. We actually have the flange nut available as a replacement part listed as part #006-092-01

view full answer...

Answer 11

Hello Mark. Based on what I could find online, the Dexter 072-042-00 is a standard 1-3/4 inch wide double eye spring which is 25-1/4 inches long and rated for 1,750 lbs. To replace these, I recommend you use the 3-Leaf Double-Eye Spring #e57SR. This…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Does Step Wet Bolt Have Torque Setting

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching