Will The MORryde Equalizers Raise The Height Of My 2018 Keystone Outback 324CG Toy Hauler?

Question

Question:

I recently installed the Morryde cre3000 and wet bolt kit on my outback 2018 324cg. Seems that it raised the hight of my trailer. I can’t find any literature or videos that mention anything about them raising the ride height. Did this kit raise my trailer and if so how much? Thanks.

asked by: Brian L

0

Expert Reply:

The MORryde Shock Absorbing Suspension Equalizers # MR87ZR are approximately 1-1/8" taller than the Curved Equalizer # TREQ104 when measured from the top bolt hole center to the center line off the lower bolt holes. This would raise the trailer height approximately 9/16". Do remember the rubber cushion used on this Equalizer does allow for the equalizer to travel up and down so at times the height could be slightly more or less depending on the weight and any road shock traveling through the suspension.

It is also important for you to verify you use the correct wet bolt kit. They offer kits with 2-1/4" Shackle Straps # MR46ZR or 3-1/8" Shackle Straps # MR76ZR. If you went from having a 3-1/8" to a 2-1/4" this would account for another 7/16" of lift.

expert reply by: Bud M

0

Answer 1

If you want the best, it's the MORryde Rubber Equalizers for Tandem Axle Trailers part #MR87ZR. These are the best as they offer the most travel which is basically how much that rubber bushing compresses and the more it compresses, the better…

view full answer...

Answer 2

Hey Scott, While we don't have a way of knowing which equalizers are on your triple axle Attitude toy hauler, we can help you figure out the right ones to upgrade your suspension. It's pretty simple, as all you have to do is measure your…

view full answer...

Answer 3

Despite what the manufacturers of these equalizers say, the axle/wheel spacing isn't the right way to figure out the best fit for upgraded equalizers, including the MORryde CRE3000. The wheel spacing is more of a guideline, so to determine the…

view full answer...

Answer 4

Thanks for the measurements and additional information! To determine which MORryde Equalizer you need you'll want to measure the distance at the bottom of your current equalizers from the center to the center of the bolt holes. The MORryde item…

view full answer...

Answer 5

Going from standard leaf springs - even with a rubber equalizer - to a whole new suspension system will 100 percent upgrade the ride of your 2021 Grand Design Reflection 303RLS. While you will certainly get some benefit by going to the Comfort Ride…

view full answer...

Answer 6

You could attach the Tow-Rax L-Track #TWSP6TAB to a composite truck bed but I would recommend using screws with nuts and washers on the other side of the track to secure it as that give you most secure attachment. Other way is using rivets which I…

view full answer...

Answer 7

The E-Track part #E19148 that you referenced is not specifically designed for a recess mount although if you wanted to come up with a way to do that you certainly could. A manufacturer was here recently and they had recessed mounted E-rack in their…

view full answer...

Answer 8

E-tracks are typically the stronger of the two, but X-track is more versatile since you can mount them horizontally or vertically. Choosing between the two really depends upon how you plan to use them. If you are installing something in a truck bed,…

view full answer...

Answer 9

In regards to trailer suspension, it's always best to swap parts with identical replacements when doing any work so you don't run into issues like you're having now with components binding or making contact. That said, I do understand…

view full answer...

Answer 10

They actually do! Furrion finally got their act together and we have the 7-Way Vehicle Power Adapter w/ Power Switch for Furrion RV Observation Camera #FR87PR hot off the press so you can use a Furrion Vision S camera system, like part #FCE48TASL-05,…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Will The MORryde Equalizers Raise The Height Of My 2018 Keystone Outback 324CG Toy Hauler?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching