Replacement Wheel Center Cap For a 2019 Coachman Apex Travel Trailer With 60C Stamped On It

Question

Question:

The hole at the outer end of the trailer wheel cap measures 1 15/16inch diameter. The pins, outside to outside, measure 1 7/8. Overall diameter is 2 3/16inch The other caps have a 60C on the inside. Do you have replacements.

asked by: Bruce D

0

Expert Reply:

We have a direct replacement for your 2019 Coachmen Apex Travel Trailer!

Check out the:

-Trailer Wheel Center Cap Plug # CCP-60C.

This center cap has an overall diameter of 2-3/16", an inside diameter of 1-13/16" and is made from ABS plastic.

expert reply by: Bryce D

0

CCP-60C Replacement Center Cap
(click to enlarge)

Answer 1

Hey Mike. The Kenda Karrier KR53 ST225/75R15 Radial Trailer Tire with 15" Black Aluminum Wheel item #KE63JV comes mounted and ready to install. However, it is not balanced and this is common amongst trailer tires. Trailer tires are lug-centric…

view full answer...

Answer 2

Hello Blake, thanks for reaching out. So trailer tires typically are not balanced the same way as vehicle tires. With trailers every wheel and tire has a high (heavy) and low (light) spot. The manufacturers offset the high spot on the tire with the…

view full answer...

Answer 3

It sounds like the remains of a double lip seal. Was it like a rubber o-ring with a metal spring around it? You are going to have to replace the seal so I would just disregard the sleeve. It would go on the outside of the rubber lip though. I…

view full answer...

Answer 4

The Prime Guard Wheel Bearing Hi-Temp Red Grease part #L11380 16-oz tub will be enough to pack the wheel bearings and grease the spindle on your travel trailer. I have attached a helpful article for your reference about packing the bearings. The…

view full answer...

Answer 5

Hello Christian, Thanks for all the information on your trailer, it is most helpful! Since you have a 3,500 pound with tapered spindles you will need the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100. It…

view full answer...

Answer 6

We recommend that you pull the hubs off your trailer to inspect and repack the bearings every 12 months or 12,000 miles. If at this time the bearings still appear in good condition then there is no need to replace them. There isn't a general rule…

view full answer...

Answer 7

Thanks for providing all of the information for your axle. This axle is going to use the standard 3,500 lb axle bearing sizing. You can use the Bearing Kit #BK2-100, which will come with bearings, races, seals, cotter pin and tang washer - everything…

view full answer...

Answer 8

Snap-In Plug for Lionshead Trailer Wheel Center Caps #LHSI60C measures 2.17 inches in overall diameter and from the outside of one tab to the outside of the opposite tab is 1.92 inches. I have included a picture showing this. This cap was designed…

view full answer...

Answer 9

That is not a typical grease cap/dust cover size, however we do have the Bearing Buddy Bearing Protectors #BB2080 which measure 2.08 inches. These caps actually make maintaining the bearings much easier and more convenient as well. I've attached…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...