Diameter of Threaded Hitch Bolt for Hollywood Racks Sport Rider and Traveler Bike Carriers

Question

Question:

What is the diameter of the HRHPN-13 bolt

asked by: Kevin R

0

Expert Reply:

The Replacement Threaded Hitch Bolt for Hollywood Racks Sport Rider and Traveler Bike Carriers # HRHPN-13 is a 1/2" - 13 bolt meaning it has a 1/2" diameter and coarse thread pitch.

expert reply by: Jon G

0

Answer 1

Sounds like what you'd need is the Replacement Threaded Hitch Bolt for Hollywood Racks Sport Rider and Traveler Bike Carriers #HRHPN-13 which is 5/8" longer than the Replacement Threaded Hitch Bolt for SportRack Bike Racks and Cargo Carriers…

view full answer...

Answer 2

It looks like you have an older Thule T2 Hitch Mount Bike Rack and the correct replacement hitch bolt/pin for this is the Thule Snug Tite Hitch Lock and Anti-Rattle Device part #THSTL2 for locking or Threaded Hitch Pin for Thule part #TH62RE for…

view full answer...

Answer 3

The other option is to use an adapter such as #HT02. This will allow you to use the 1-1/4 inch bike rack shank in a 2 inch receiver.

view full answer...

Answer 4

The correct replacement hitch pin for your Thule Trailblazer Bike Rack 998 is the Thule Replacement Hitch Pin Assembly for Bike Carriers part 853-5019-02. The problem is that this pin is no longer made as the rack is very old and there isn't a…

view full answer...

Answer 5

Yes the threads are 12mm x 1.75. The threaded portion is 1 3/8" long and the non threaded length is right at 3".

view full answer...

Answer 6

All Thule bike racks use the same threaded hitch pin so you can use the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #853-5917. This is just the threaded bolt, and you'll need to use the flat washer, lock washer…

view full answer...

Answer 7

The hitch pin bolt you'll need for a Thule bike carrier/rack is the Replacement Threaded Pin for Thule part #853-5917. It is indeed an M12x1.75 bolt which is roughly 4" long. I can't confirm compatibility of thread pitch for the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Diameter of Threaded Hitch Bolt for Hollywood Racks Sport Rider and Traveler Bike Carriers

Product Page this Question was Asked From

Continue Researching