Correct Replacement Fan Blade For The Newer 1-1/2" 12V Motor For Ventline Ventadome Fans

Question

Question:

I do have the 1.5inch size newer fan motor in a 21 Airstream, but need to confirm that this is the blade with round not D-section spindle hole. Thanks!

asked by: Curt

0

Expert Reply:

As long as you have the 1-1/2" motor # BVD0218-00, then the Replacement Fan Blade for Ventline Vanair Trailer Roof Vent # BVD0217-00 is the correct replacement fan blade.

expert reply by: Bryce D

0

Answer 1

The Replacement Fan Blade for Ventline Vanair Trailer Roof Vent part #BVD0217-00 has a very small 0.03" hole in the center of the fan blade. The blade is the replacement blade for Ventline Vanair Trailer Roof Vent w/ 12V Fan - 6-1/4"…

view full answer...

Answer 2

The center hole on the fan blade for your Ventline Vanair Trailer Roof Vent w/ 12V Fan #VP-543SP is 0.03" in diameter. For a replacement fan blade, you can use the: -Replacement Fan Blade for Ventline Vanair Trailer Roof Vent #BVD0217-00. This…

view full answer...

Answer 3

The Replacement Fan Blade for Ventline Vanair Trailer Roof Vent #BVD0217-00 is the correct replacement fan blade for your Philips Product Ventline 12 V DC. 1.5 A V147-16 Model VP. I do not have the height of the fan blade, but I did confirm with that…

view full answer...

Answer 4

We have the Replacement Push-Button Switch #BV0199-03 that fits with the hole in the Replacement Screen Frame #BVC0515-05. The Replacement Fan Blade #BVD0217-00 works with the 1-1/2" long Replacement 12V DC Motor #BVD0218-00. You will need to…

view full answer...

Answer 5

Hey Charles, thanks for reaching out! The Ventline Breeze LED 360 Bathroom Vent w/ 120V AC Fan #VE76FR can be used in a standard house since it runs off of 120V power as opposed to 12V power. This has an 11-3/8" overall diameter but fits into a…

view full answer...

Answer 6

For the P series of Ventline fans, such as Model PH 4, the correct replacement fan motor is #BVD0278-00. Should you have an older motor, you may also need a new fan blade which is compatible. You will want to measure your old motor from end to end,…

view full answer...

Answer 7

The switch is not included with the replacement fan motor #BVD0218-00. You can use switch #BL0108-00. For a fan blade there are 2 options that fit the motor depending on the type you need. First we have the replacement fan for Ventline Ventadome…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Correct Replacement Fan Blade For The Newer 1-1/2" 12V Motor For Ventline Ventadome Fans

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching