What Bearing Protectors Fit My Mastercraft Boat Trailer?

Question

Question:

Hi, Im looking for a bearing protector for a Mastercraft trailer for a 2003 X10 boat. Its a single axle trailer with 6 lug nuts per wheel. The old bearing protector had Reliable written on it and was made out of plastic. It screws in and the diameter of the threaded part is 2.5 in. The trailer model and serial number is SA-05-MS210, B9-000045.

asked by: Stefan S

0

Expert Reply:

While I unfortunately could not find any specs on your Mastercraft trailer with serial numbers SA-05-MS210 and B9-000045, there is a definitive way you can measure your trailer to get the correct bearing protector size you need.

In order to determine your size, you need to confirm the diameter of your hub's bore opening. This size determines what bearing protectors you need. For instance, if you find that your bore is 2.441" in diameter, you would need the Bearing Buddy Bearing Protectors - Model 2441T-SS # BB2441T-SS. Since the measurement needs to be precise, I recommend using calipers like the # PTW80157 to make your hub bore measurement.

expert reply by: Bob C

0

Answer 1

It sounds like your problem may be that you are installing too much grease into the hubs and that is why they are blowing out. If you are pumping your grease into your hub with a grease gun you should note that you should only continue to add grease…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

What Bearing Protectors Fit My Mastercraft Boat Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching