Pilot Hole Diameter Needed for 1-1/2" Long Torx Floor Screws TF01150

Question

Question:

What size pilot hole do you recommend for a 5/16 screw

asked by: Scott L

0

Expert Reply:

A 7/32 size drill bit would be ideal as a pilot hole size for use with the 1-1/2" Long Torx Floor Screws # TF01150 which are actually 1/4 inch diameter.

expert reply by: Jameson C

0

Answer 1

You will want to use the 1-1/2" Long Torx Floor Screws #TF01150 to hold your 5/8" marine treated plywood on your snowmobile trailer. These screws are the same 1/4" diameter you removed from your previous flooring. They are 1-1/2"…

view full answer...

Answer 2

I do have a solution for you but the 1-1/2" Long Torx Floor Screws #TF01150 are not treated so these would not be ideal for the use you have in mind. The 1-1/2" Long Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood #TFX150ACQ…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Pilot Hole Diameter Needed for 1-1/2" Long Torx Floor Screws TF01150

Product Page this Question was Asked From

Continue Researching