Is There a Plug-And-Play Brake Controller For 2022 Acura MDX

Question

Question:

Hello, Im looking for plug-in brake controller to Acura MDX 2022. factory tow package with 7-way

asked by: Alex

0

Expert Reply:

Since you have a 7-way, there is one brake controller that you just have to plug in and no other wiring is needed, the Curt Echo Wireless Brake Controller # C51180.

expert reply by: Kyle S

0

Answer 1

Yes, the etrailer Surge Brake Coupler Lock #e98888 will allow you to lock the Dexter DX7.5L A-60 Brake Actuator #DX56FR to your 2" hitch ball. We also have the Blue Ox Hitch Receiver and Coupler Latch Lock Set #BLU36XR if you want a matching…

view full answer...

Answer 2

You actually need the reverse light circuit active on your trailer wiring so that your surge brakes can be temporarily deactived when backing up. So what you'd need is a 4-way to 7-way adapter #37185 and you'd need to connect the purple wire…

view full answer...

Answer 3

Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a…

view full answer...

Answer 4

If the solenoid is getting a full 12 volts and is grounding properly it should be shutting all the way. Since you said it is clicking that makes it sound like it's getting power. You could try improving the ground circuit but most likely…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Is There a Plug-And-Play Brake Controller For 2022 Acura MDX

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching