Air Lift Load Lifter Kit that Fits 1989 Toyota 1-Ton National RV Dolphin

Question

Question:

1988 Toyota 1-ton chassis, dual rear wheels, VIN code ending with 3W. 1989 National RV Dolphin motorhome is mounted atop the Toyota 1-ton chassis. Will the AirLift air springs/bags kit #AL88113 fit in the above combination? Also, how long are the supplied air lines for the air valves to fill? Original airbags are Firestone AirSleeve model #3Q86 and these are mounted slightly in front of the axle Thank you.

asked by: Tucker

0

Expert Reply:

For your 1989 Toyota Motorhome National RV Dolphin the Air Lift LoadLifter 5000 part # AL88113 is a confirmed fit and would work great. The length of the included air line is 15 feet.

expert reply by: Jameson C

0

Answer 1

Hey Todd. I wasn't able to get anything off of the 2024015099 number you gave me. The 2nd generation replacement front jacks that fit the first generation Level Up systems are listed below: Lead Leg - Replacement Hydraulic Jack Assembly for…

view full answer...

Answer 2

I have two airbag kits confirmed to fit your 1986 Toyota Dolphin Motorhome. You can use either the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers part #AL88113 or the Air Lift LoadLifter 5000 Air Helper Springs part…

view full answer...

Answer 3

Hey Vic, welcome back. The Air Lift Ride Control Air Helper Springs item #AL59502 is a complete air bag kit for a 1986 Toyota Pickup. It includes two air springs, all the mounting brackets, and fittings. We do not have a replacement air bag for this…

view full answer...

Answer 4

The only air bag suspension kit that is compatible with your 1987 Toyota Motorhome Chassis comes from Air Lift with the kit #AL88113. You might also be interested in adding an air compressor kit to help make monitoring and adjusting your air bags…

view full answer...

Answer 5

Atwood water heaters have been discontinued for quite some time as Atwood is no longer in business. Even standard water heaters are getting rarer as most people switch to tankless. That's what I highly recommend checking out to save energy and…

view full answer...

Answer 6

Hello Kent, thanks for reaching out. I am a bit of a Toyota enthusiast so I always get stoked to see these old Toyotas still on the road. I own a 2006 and a 2010 Corolla and they are just amazing cars. They don't make 'em like they used to…

view full answer...

Answer 7

Hey Steve, The AirLift airbags with internal jounce bumpers are not able to be added to a system without so you would need to get a whole new system. With that said the system with the internal jounce bumpers is going to create a much rougher ride…

view full answer...

Answer 8

While you can technically use the Yakima Exo Swing Away Storage System #Y44ZR on a front hitch, I confirmed with Yakima that they haven't physically tested that application. With that being said, I do have the measurement you requested. The…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Air Lift Load Lifter Kit that Fits 1989 Toyota 1-Ton National RV Dolphin

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching