Replacement 14,000 lb. Hydraulic Jack Assembly for Lippert Level Up Systems

Question

Question:

Hello I was wondering if you guys carry a Lippert Hyrdaulic jack with the Lippert part number of 2571254 or 25712510. Thank you,

asked by: Aaron V

0

Expert Reply:

We do carry some Lippert Hydraulic jacks but none by those part numbers. I tried looking them up on Lipperts site and found nothing on the 2571254 number and the 25712510 seems to have been superseded by a jack with a 14,000 lb. capacity, but not one that we carry.

We do carry the Replacement Hydraulic Jack Assembly for Lippert Level Up System - 14,000 lbs # LC99ED which works with the Lippert Components Level Up RV leveling system.

expert reply by: Scott S

0

Answer 1

Here is a list of all the Lippert Level Up replacement jacks we offer. Currently this is the only way Lippert offers their jacks and they do not offer a rebuild kit for these. Replacement Hydraulic Jack Assembly for Lippert Level Up RV Leveling…

view full answer...

Answer 2

Yes, as a matter of fact we have just what you need. The Replacement Hydraulic Jack Assembly for Lippert Level Up System #LC99ED is the Lippert 236560 part you mentioned. This jack has a maximum weight capacity of 14,00lbs, and measures 21-7/8"…

view full answer...

Answer 3

Hey James, we need to figure out what leveling system you have on your 2005 Holiday Rambler Ambassador 40 foot and determine if we have a replacement front jack for it. Is there any part number or brand info you can see on the jack leg? If you can…

view full answer...

Answer 4

Yes we do, the correct oil seal you would need is the part #10-56 which I verified has same dimensions as the 295924 that you have now.

view full answer...

Answer 5

Hi Douglas; thank you for providing that information down below. What you have now is the 25712510. The correct replacement leg is the Replacement Hydraulic Jack Assembly for Lippert 5th Wheel RV Leveling System - 14,000 lbs - Gen 1 #LC25AF. The…

view full answer...

Answer 6

Hello Sal, Since you have the 1st Generation silver with 6 holes, you are going to want the Replacement Hydraulic Jack Assembly for Lippert Level Up 5th Wheel RV Leveling System - 14K - Gen 1 #LC25AF. You are probably thinking, "I said 6 holes,…

view full answer...

Answer 7

It is normal for your Lippert hydraulic jack to take 3-4 minutes to retract, according to my contact at Lippert. You really will only have to worry about operation if you aren't able to manually retract the jack. There should be a plug you can…

view full answer...

Answer 8

It sounds like you need to perform a zero point calibration since you replaced your Jack #LC99ED. Here are the steps you will need to perform. Level Zero Point Calibration To set the zero point (controller module must be fully secured in…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement 14,000 lb. Hydraulic Jack Assembly for Lippert Level Up Systems

Continue Researching