Can Happijac 4800 4160 Camper Jacks be Converted from Manual to Electric

Question

Question:

Looking to get a motor kit for my Happijac 4800 and 4160 jacks. I think its part number 182522.

asked by: Erik

0

Expert Reply:

We have just what you're looking for. The Manual-to-Electric Conversion Kit for HappiJac Truck Camper Jack Systems # LC733960-182524 is compatible with your HappiJac 4160 4820 Series jacks and will allow you to convert your system from manual to electric jacks.

expert reply by: Jameson C

0

Answer 1

We have just what you're looking for. The Manual-to-Electric Conversion Kit for HappiJac Truck Camper Jack Systems #LC733960-182524 is compatible with your HappiJac 4160 Series jacks and will allow you to convert your system from manual to…

view full answer...

Answer 2

The grease seal that comes with the bearing kit part #BK2-100 that you referenced is correct for your 2018 R-Pod 178 that you referenced. The inner and outer diameters are close enough that the fit would be good. If you needed just the seal it's…

view full answer...

Answer 3

The Replacement Converter Section for Progressive Dynamics 4000 Series RV Power Control Center part #PD4045CSV is a direct replacement for the converter section on the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger part…

view full answer...

Answer 4

You can connect the Progressive Dynamics 4000 Series Inteli-Power Converter #PD4045KA just to shore power to power your AC and DC appliances. The batteries are not necessary.

view full answer...

Answer 5

The heads that come with the Replacement Motor Heads w Circuit Board and Remote #LC733960 measure 9-1/8" from the bolt hole that connects them to the legs up to the topmost part of the motor (see attached). Hopefully this will be enough…

view full answer...

Answer 6

If you have the HappiJac 4800 series jacks you can add the Manual-to-Electric Conversion Kit #LC733960-182524. This will give you the ability to control the jacks from the included remote. The Remote #HJ54ZR will allow you to operate the jacks…

view full answer...

Answer 7

The replacement motor kits that you are seeing will not work with the 4800 series jacks. The 4800 series, uses the 182522 motors and we do not carry them. The 4800 series was discontinued, making it more difficult to find replacement parts. With the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can Happijac 4800 4160 Camper Jacks be Converted from Manual to Electric

Product Page this Question was Asked From

Continue Researching