Correct CE Smith Trailer Hub Assembly for BTR E-Z Lube Spindle 2,500 Lb Axle

Question

Question:

Will these 2 items work together? Product Detail Qty Total CE13100CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded - CE13100 TRU27FRBTR E-Z Lube Spindle w/ Brake Flange for 2,500-lb Trailer Axles - 1-3/4 Diameter - TRU27FR Remove

asked by: Terence

0

Expert Reply:

The BTR E-Z Lube Spindle part # TRU27FR uses L44649 bearings so the CE Smith Trailer Hub Assembly part # CE13109 would be correct.

expert reply by: Conner L

0

Answer 1

Yes, the 2 Trailer Idler Hub Assemblies #TA88545-2 will fit on 2 of the BTR E-Z Lube Spindles #TRU27FR. The hubs include the correct Bearings #L44649, Races #L44610, Seals #RG06-020 and Grease Caps #RG04-040 for the spindle.

view full answer...

Answer 2

Yes, you would! The BTR E-Z Lube Spindle w/ Brake Flange item #TRU27FR you were looking at has an outer diameter of 1.063" which corresponds to a item #L44649 bearing. We don't have pillow bearings.

view full answer...

Answer 3

In order to find the correct replacement hub and spindle you will need to know the capacity of your axle along with the bearings you currently have. In order to find the size of the bearings you can look for part numbers on your existing bearings. If…

view full answer...

Answer 4

For a hub that is compatible with a 10 inch wheel and has a 5 on 4-1/2 inch bolt pattern you would want the Dexter part #8-259-50 and then for a spindle part #TRU97FR .

view full answer...

Answer 5

I have a recommendation as we do not have any hubs that will use the bearing combination you have. I recommend replacing your spindles with the BTR E-Z Lube Spindle #TRU27FR. This will upgrade you to a more commonly found spindle size that use the…

view full answer...

Answer 6

You will need 2 of the Easy Grease Trailer Idler Hubs #AKIHUB-545-2-LFEZ-2K for your trailer hubs. This hub fits on your Spindle #TRU27FR and will include new bearings, races, a grease seal, grease cap, and new lug nuts. As you have an EZ grease…

view full answer...

Answer 7

The Lippert Lubed Straight Spindle with Brake Flange #TRU27FR has a stub diameter of 1-5/16" and is designed to fit a 2,500-lb axle. If your tow dolly has those specifications, this spindle will work on your axle. If you're not sure, check…

view full answer...

Answer 8

Axle capacity is usually noted on a sticker or plate on the axle itself. The linked article includes a table with typical axle capacities based on their diameter; this information appears in the first column. Selecting new hubs requires you to match…

view full answer...

Answer 9

Yes, the Dexter hub part #8-258-50UC1-EZ has a 5 on 4-1/2 inch bolt pattern and fits the spindle part #TRU27FR.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Correct CE Smith Trailer Hub Assembly for BTR E-Z Lube Spindle 2,500 Lb Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching