Tucson Directlink Brake Controller is Fully Functional but the Display Screen is Not Working

Question

Question:

I got a 2008 Airstream Interstate on a Freightliner chassis. It already has a Tucaon Direclink brake controller installed. When hooked up to a trailer, the controller activates the trailers brakes, but the screen on the controller wont come on. I cant tell what my brake gain is set at. Is this an issue with the unit or is there something Im doing wrong?

asked by: Dustin G

0

Expert Reply:

I just spoke with my rep at Tuson RV Brakes, the manufacterer of the Tuson DirecLink Base Model Trailer Brake Controller item # 335DL-100. He said that the older units had an LCD screen that wears out over time depending on the region you live in. He said humidity gets into the display and it slowly begins to fade until the entire screen goes dark. He told me there's most likely nothing wrong with your controller and you haven't done anything wrong but you will need to replace it with the newer upgraded LED display screen they have now. You will need to contact them directly at 800-968-8766 and speak to their warranty department at ext 220. If your Tuson DirecLink Base Model Trailer Brake Controller item # 335DL-100 is not covered under warranty the model we sell does come with the newer LED screen.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 7

Hey Bo! To set up your semi for a standard 7-way plug, you will first need the Curt Powered Tail Light Converter item #C59496, which would tap into the circuits feeding your tractor trailer 7-pin round plug. The yellow wire taps into the feed for the…

view full answer...

Answer 8

For your Peterbilt 335 I definitely recommend going with the Tekonsha Prodigy P3 Trailer Brake Controller #90195 over the Hayes #HA100400C because it's going to allow for a much easier install and is more economically priced. The P3 also offers a…

view full answer...

Answer 9

Hello Ronald, thanks for reaching out. The best thing to do here will be to use the Hayes Air Actuated Trailer Brake Controller #HA100400C. This will allow you to control the electric brakes on your 5th wheel with your 2013 Peterbilt 337 day cab with…

view full answer...

Answer 10

The Curt True Course Advanced Bluetooth Trailer Sway Control #C94VV wins for ease of install and it does a really good job but if you were wanting the best sway control that applies the left and right brake assemblies independently the Tuson…

view full answer...

Answer 11

Hey Ken! The correct wiring harness depends on whether or not you have the brake controller port/plug. Some models did not include the plug so you will have to check your 2025 Ranger and see. There should be four wires coming out of a large wire…

view full answer...

Answer 12

Hey Ray, thanks for reaching out! The Tuson DirecLink Base Model Trailer Brake Controller #335DL-100 can definitely be used with your 2005 Freightliner Century Class either by splicing in the wiring or using one of the following adapters if they…

view full answer...

Tucson Directlink Brake Controller is Fully Functional but the Display Screen is Not Working

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching