Matching Nut for Replacement Vertical Bolt RM-350190-20 for Roadmaster Sterling Tow Bar

Question

Question:

Is the replacement nut 350255-00, the nut for this bolt? .. does it also use a washer?

asked by: Kamron

0

Expert Reply:

I pulled up the manual for a Roadmaster Sterling tow bar and the matching nut to go with the # RM-350190-20 is the # RM-350267-01 actually. A washer is required.

expert reply by: Jameson C

0

Answer 1

Are you possibly looking for the replacement bushing part #RM-200029-10 which is the yoke bushing? Or we have the Nylatron split bushing part #RM-200029-00. Sounds like you are in need of both of these. Let me know either way though.

view full answer...

Answer 2

We do have the Complete Repair Kit for Roadmaster Sterling Tow Bar #RM-910003-30 as the Kit #RM910003-85 is for Falcon and Blackhawk tow bars. We also have the following parts if they are damaged and need replaced on your tow bars. Inner Arm Bushing…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Kevin, welcome back! You are correct, since you have ParkSense on your 2026 Rubicon the #RM-152 is not the correct wiring kit. What you need instead is the Roadmaster Smart Diode Kit for Variable Voltage LED Tail Lights #RM47ZR. This will get…

view full answer...

Answer 11

Hey Jim. The Curt Custom Tail Light Wiring Kit for Towed Vehicles item #C96JR is indeed compatible with the LED lights on your 2025 Jeep Wrangler Unlimited. It plugs into your factory wiring harness behind the tail lights. The only issue would be if…

view full answer...

Answer 12

Hey Robert, the only frame mounted base plate kits we have for your 2021 Jeep Wrangler Unlimited like the Roadmaster part #RM-521453-5 require either the factory steel or plastic bumper to verify for sure they will work. For aftermarket bumpers you…

view full answer...

Matching Nut for Replacement Vertical Bolt RM-350190-20 for Roadmaster Sterling Tow Bar

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching