Equal-i-zer Hitch Shank that Can be Used in 2-1/2 inch Hitch

Question

Question:

I have an Equal-i-zer hitch model 90-00-1200/12,000lbs. It has a 2 inch shank that goes into the receiver on my vehicle, but the Ford F-250 Super Duty truck I am planning to order comes with a 2.5inch receiver. Can the shank on my hitch be replaced with a 2.5inch hank and, if so, can you tell me the part number for that shank so I can see what it would cost? Thank.

asked by: Doug C

0

Expert Reply:

You can easily swap the shank of your Equal-i-zer kit to fit a 2-1/2 inch hitch with the part # EQ90-02-4900 which is exactly what you are looking for.

expert reply by: Jameson C

0

Answer 1

I went to the warehouse and measured the #EQ90-02-4800 for you. The hitch pin hole to the holes on the vertical leg of the shank measures 8 inches. The overall length is 12 inches. We do have another shank. It is part #EQ90-02-4900. The overall…

view full answer...

Answer 2

The best way to proceed is to definitively identify the tongue weight of the trailer when it's loaded as it typically would be when you tow. I'll link to an article that explains a few ways to do this, but the easiest method is to use a…

view full answer...

Answer 3

Based on what you described you need a weight distribution shank that can do 3 inches of drop. The Equal-i-zer Weight Dist Shank #EQ90-02-4800 can provide up to 4 inches of drop and would work well for your new truck that has a 2-1/2 inch hitch.

view full answer...

Answer 4

Since you are at point where you should probably go to a higher tongue weight range setup, you need a new shank, and the bars and heads of the Equal-i-zer have to be replaced together if changing tongue weight range you'd be best served to go…

view full answer...

Answer 5

Based on the pictures you attached (thank you!) it looks like you have the Equal-i-zer Weight Distribution Shank #EQ90-02-4100 that allows for a drop of up to 3 inches from the top of the hitch receiver opening. The adjustment portion of the shank…

view full answer...

Answer 6

view full answer...

Answer 7

Most of our weight distribution systems do not come with a 2-1/2" shank. Some do but your options are limited at that point. The best solution I have for you would be to choose the weight distribution system you want without a shank, and use a…

view full answer...

Answer 8

I do have a solution for you, but you will need to use a weight distribution shank that is compatible with your Equalizer #EQ37100ET weight distribution system and not one that has been altered. I recommend using the Equal-i-zer Weight Dist Shank -…

view full answer...

Answer 9

For 2-1/2 inch hitches we have the hitch lock part #e98881 which is going to be a great option for you. It has a usable span of 3-5/8 inches which would easily fit your hitch and ball mount. This has a 5/8 inch diameter which is the correct size for…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Equal-i-zer Hitch Shank that Can be Used in 2-1/2 inch Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching