What Plug-and-Play Wiring Harness Works with the Curt Spectrum for My 2022 Jeep Grand Cherokee?

Question

Question:

i have a 7-way already installed on my 2022 Jeep grand Cherokee as well as a tow package. What plug and play wiring harness do I need for the curt spectrum C51170?

asked by: Glen

0

Expert Reply:

For the correct plug-and-play wiring harness to go with the Curt Spectrum Trailer Brake Controller # C51170 on your 2022 Jeep Grand Cherokee with a 7-way and tow package, that is the Curt Custom Wiring Adapter for Trailer Brake Controllers # C51446. With this adapter, you will be able to simply plug in the Spectrum wiring right into the port under your dash for easy installation.

expert reply by: Bob C

0

Answer 1

Yes the Bearing Buddy part #BB1980A-SS is correct for the Dexter hub you have #8-247-50UC3 and then for the bearing kit part #BK2-100 is also correct! You made my job easy.

view full answer...

Answer 2

Yes you can use a Bearing Buddy on your current axle setup but you'll have to remove the zerk/grease fitting. What you have now is an EZ lube spindle which allows you to push grease through the middle of the spindle but you can install a Bearing…

view full answer...

Answer 3

When using an EZ-Lube hub, such as hub/drum assembly #AKHD-545-2-EZ-2K, on an EZ-Lube spindle it is not necessary to also use Bearing Buddy bearing protectors. An EZ-Lube spindle, such as part #TRU44FR, has a grease zerk fitting to allow you to pump…

view full answer...

Answer 4

EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…

view full answer...

Answer 5

All of our bearing kits, like the part #BK2-100 that was referenced, only include the inner/outer bearings, grease seal, and cotter pin/washer but I can help you get the other parts that you are needing as well. For 10" x 2-1/4" brakes we…

view full answer...

Answer 6

I reached out to my contact at Dexter and was able to get the wheel bearing numbers you need for your 1999 Jayco Pop-Up Camper. The inner bearing is #L68149 and the outer bearing is #L44649. I recommend getting the complete kit which is Bearing Kit…

view full answer...

Answer 7

For an 84 spindle the correct castle nut would be item #165686 which is a 1 inch spindle nut. It has 14 threads per inch.

view full answer...

Answer 8

The TruRyde Spindle Nut #165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist.…

view full answer...

Answer 9

The Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles #BK2-100 does not come with the grease cap and spindle nut. You will have to purchase them separate. The Grease Cap #RG04-040 has a 1.99 inch outer diameter. The cap has a drive-in…

view full answer...

Answer 10

The Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-35-G-EZ-K does not come with the spindle nut. That would come with your axle. For a 3,500 lb axle you would want the Spindle Nut Kit for EZ Lube Axles…

view full answer...

Answer 11

Any time your vehicle is placed in reverse, whether you are towing or not, the alarm will sound on the Curt Trailer Connector Adapter with Backup Alarm item #C57102. To have the same connector without the beeping sound you will want the Curt Trailer…

view full answer...

Answer 12

You can absolutely store the Hopkins Plug-In Simple Vehicle Wiring Harness #HM11143865 in the hatch of your 2013 Subaru Outback when you aren't using it instead of routing it outside the vehicle. The connector end will be long enough to hang…

view full answer...