What Are The Steel Plates In The RAS System Used For.

Question

Question:

where does the flat plate with the hole in the center go ? 2016 gmc 2500 4wd

asked by: Kevin C

0

Expert Reply:

The plate you are referring to in the RoadActive Suspension Custom Leaf Spring Enhancement Kit - Heavy Duty
# RAS3611-CHD will replace the upper overload on your suspension if you have it.

expert reply by: David B

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What Are The Steel Plates In The RAS System Used For.

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching