Comparing Trailer Wiring Junction Box 3375601100 and Trailer Wiring Junction Box 38656

Question

Question:

Spectro Item # 38656 vs Polypropylene Item # 3375601100 Is one better than the other?

asked by: John

0

Expert Reply:

The Trailer Wiring Junction Box part # 3375601100 and Trailer Wiring Junction Box part # 38656 are both pretty standard 7-terminal junction boxes. The latter is slightly smaller so there will be more places to mount it so that is what I recommend but you really can't go wrong with either option.

expert reply by: Conner L

0

Answer 1

The ring terminals you want to use with the junction #3375601100 are the #44-5310A which have an inner diameter of 3/16 of an inch.

view full answer...

Answer 2

There are 2 different possible connectors you can use for the wiring when it comes to the GloLight LED Trailer Tail Light #STL101RMB; the 3-Wire Pigtail #A45PMB which installs using splicing, and the Three-Wire Straight Pigtail #AL45PWTB which…

view full answer...

Answer 3

The Trailer Wiring Junction Box #3375601100 has dimensions of 8-1/2" long, 3-5/8" wide and 2-1/2" tall. The distance between the mounting holes (center of hole to center of hole) is 7-13/16". I have included a video that shows…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Comparing Trailer Wiring Junction Box 3375601100 and Trailer Wiring Junction Box 38656

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching