Folded Dimensions of Torklift Glowstep part # TLA7804

Question

Question:

what are the dimensions of the steps when they are collapsed folded up for the #TLA7804?

asked by: Hank

0

Expert Reply:

When folded the Torklift Glowstep part # TLA7804 is 15 inches tall, 21-1/2 inches wide, and 8-9/16 inches deep.

expert reply by: Jameson C

0

Answer 1

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Answer 2

While we do not have a video of these steps being specifically installed on your camper I took a look at the instruction manual, which is also linked, and there is a method for installing these steps on a camper that does not have a bumper. You would…

view full answer...

Answer 3

The SafeStep Vinyl Barrier #TLA7602 was designed for the TorkLift GlowStep Scissor Steps but could potentially be used for any set of scissor steps. You just may need to trim them down to size if they are too large. The TorkLift SafeStep Vinyl…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item #LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Folded Dimensions of Torklift Glowstep part # TLA7804

Product Page this Question was Asked From

Continue Researching