Will This Brass Connector For Titan Disc Brake Acutators Fit My UFP A-60 Master Cylinder

Question

Question:

Will this work on an UFP A-60, model number ST-UFP34043, master cylinder for single axle disc brakes using 3/16 brake lines?

asked by: Glenn A

0

Expert Reply:

Yes, I spoke with someone from Dexter today and they said the Replacement Brass Connector for Titan Disc Brake Actuators - Qty 1, part # T4750300 will fit your brake actuator.

expert reply by: Mark Smith

0

Answer 1

The part you are looking for is the Brass Connector for Titan Disc Brake Kit, #T4750300. This is the fitting that threads into the master cylinder that accepts the reverse lockout solenoid on your Titan actuator. I have attached a link to this part…

view full answer...

Answer 2

Yes the Replacement Brass Connector #T4750300 for Titan Disc Brake Actuators will fit a Tie Down 660e disc brake actuator.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Will This Brass Connector For Titan Disc Brake Acutators Fit My UFP A-60 Master Cylinder

Product Page this Question was Asked From

Continue Researching