What Size Nut Is Used To Secure Spare Tire To Draw-Tite Front Mount Spare Tire Carrier 6715?

Question

Question:

The hardware that comes w/ this spare tire carrier, what kind of lug nut does it accept? Will an M12-1.50 work?

asked by: Joseph A

0

Expert Reply:

The Front Mounted Trailer Hitch Universal Spare Tire Carrier # 6715 you were looking at does not use standard lug nuts, and needs to use the included washers, and nuts.

The bolts included with the hitch are 7/16-14 grade 5 bolts, so your M12-1.5 lug nuts will not fit.

I included a video of the # 6715 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Yes the hitch mounted spare carrier part #6715 can fit the hitch you have at the rear of your Minnie Winnie.

view full answer...

Answer 2

CE Smith Spare Tire Cover #CE27440 is designed to be slipped over a mounted spare tire. It does not require you to unbolt the spare from the trailer or tire carrier. If you refer to the linked photo you'll see how the elastic hem snugs the cover…

view full answer...

Answer 3

The 225/75-16 tires are about 29.29" in diameter. For that size I recommend Rampage Spare Tire Cover part #RA773201 which fits 30" to 32" diameter tires. It is a nice black UV-resistant material to avoid breaking down over time. The…

view full answer...

Answer 4

The instructions included with the Thule RV Wheel Levelers #TH307617 do state that the tires should be 20mm narrower than the width of the levelers for even support across the tires. That being said, these levelers are intended for motorhome use and…

view full answer...

Answer 5

What you'll do is use a separate wheel chock behind the wheels after using the Thule RV Wheel Levelers #TH307617. All you need to use is the Buyers Products 10" Wheel Chock #337WC1086UWH.

view full answer...

Answer 6

As long as there's a hitch at the back of your trailer the Spare Carrier part #6715 will work fine for you.

view full answer...

Answer 7

When a tire is attached to the universal spare tire carrier, #6715, the tire will be at a slight angle; maybe 10 degrees off from a straight up and down 90 degrees. The top of the tire will be slightly closer to the vehicle than the bottom like in…

view full answer...

Answer 8

According to my Draw-Tite representative, the #6715 spare tire carrier should work with your 8-lug wheel as long as it doesn't weigh above 100 lbs.

view full answer...

Answer 9

I have an option with less of an angle but there is not an option that is perfectly vertical besides the Roadmaster Spare Tire carrier part #RM-195125 like you mentioned. However, the Draw-Tite Spare tire carrier option part #6715 has less of an…

view full answer...

Answer 10

Your tire size of P225/65R17 has an overall diameter of 28.7 inches. So for that the part #CE27440 would be an excellent option confirmed as a fit. This cover will not fly off as it will be very snug once installed.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

What Size Nut Is Used To Secure Spare Tire To Draw-Tite Front Mount Spare Tire Carrier 6715?

Featured Help Information

Miscellaneous Media

Continue Researching