What Side of Axle Does SumoSprings Trailer Helper Springs # TSS-106-40 Install On

Question

Question:

Does the helper spring go on the frontside or backside of the axle.

asked by: Charles C

0

Expert Reply:

You'd want to install the SumoSprings Trailer Helper Springs # TSS-106-40 on the front side of your axle.

expert reply by: Jameson C

0

Answer 1

The height of the SumoSprings Trailer Helper Springs w/ Line Relocation Bracket #TSS-106-40 is 4 inches for just the rubber spring portion of it. Since you have 3 inches from the axle to the frame that would indicate that there would be a compression…

view full answer...

Answer 2

The Viair Portable RV Air Compressor Kit for 5th Wheels and Travel Trailers part #VA39WR is a bit too small for 35" tires. Instead, you'd need to bump this up to the next size which is the Viair Automatic RV Portable Air Compressor for Class…

view full answer...

Answer 3

You want between 1/4" and 1/2" of preload on the SumoSprings Trailer Helper Springs item #TSS-106-40. If not you'll get a harsher ride quality because the springs will always been engaged or you'll get nothing out of them because…

view full answer...

Answer 4

Hey Carl, thanks for writing in, and that's a good question. Thankfully, the answer is no, you do not need to cut or trim the fascia/face plate on a 2024 Ford Maverick to install the Demco base plate that fits, which is the following part number:…

view full answer...

Answer 5

A typical tire inflator will have a CFM rating of around 1.5 to 2 CFM, with a majority of the little cheap ones being less than 1 CFM. The higher the rating the faster you'll be able to air up the tires. The Viair Automatic Portable Air…

view full answer...

Answer 6

I recommend staying with the 4-Leaf Double-Eye Spring for 3,500-lb #e54SR. This will ensure that you do not have to change other parts of your suspension system and the trailer has the correct ride quality. The 4-Leaf Double-Eye Spring for 4,000-lb…

view full answer...

Answer 7

According to SumoSprings, 6" is the minimum for the #TSS-106-40. I asked them about this and they said you cannot use these if the space is under 6" so unfortunately they won't work for you. Doing so will overload the springs which can…

view full answer...

Answer 8

The SumoSprings Trailer Helper Springs part #TSS-106-40 per the instructions will be installed on the side of the axle closest to the end of the leaf spring that is connected to a shackle or center link.

view full answer...

Answer 9

There are a few things that can cause bounce with a bumper pull trailer. Generally, bias ply tires would not contribute to trailer bounce, unless they are excessively worn. Trailer bounce is can be caused by worn out suspension components. You will…

view full answer...

Answer 10

If your trailer has a GVWR of 3,750lbs and your boat only weighs 1,460lbs you should be fine with the 3,500LB Leaf Springs #e54SR. I would recommend taking your boat and trailer to a nearby scale to have the trailer weighed to ensure you are under…

view full answer...

Answer 11

The Dexter Trailer Springs Over-Under Conversion Kit #K71-385-00 would help increase the space between your tires and fenders. This kit works for 3" diameter axle tubes and is the simplest solution. For 2-3/8" axles you can use this kit…

view full answer...

Answer 12

You can eliminate the bounce in your trailer and smooth your ride with the addition of Sumo Springs. You will have two options, depending on how your leaf springs are mounted on your trailer. If your leaf springs are underslung, meaning they are…

view full answer...

What Side of Axle Does SumoSprings Trailer Helper Springs # TSS-106-40 Install On

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching