Replacement Curt Trailer Hitch Receiver Hardware for 2008 Nissan Xterra

Question

Question:

Hi, I bought a used Curt trailer hitch for my 2008 Nissan Xterra. Unfortunately the person didnt have the bolts or washers to install. What size bolts and washers do I need? Thanks

asked by: Peter

0

Expert Reply:

The Curt Trailer Hitch Receiver # 13514 will use 4- M14 bolts with 9/16" lock washers and 2- M12 bolts with 1/2" conical toothed washers.

I recommend the Replacement Hardware Kit for Trailer Hitches # RHK. You will just need to input that you have a Curt hitch item number 13514 when ordering. This will ensure that you get the exact size and grade hardware for your hitch.

expert reply by: Bud M

0

Answer 1

A hitch from a 2004 Xterra will not fit a 2010 Nissan Xterra. For a hitch that does fit your '10 Xterra you need the following: - Trailer Hitch Receiver #e27AR If you also need a 4-way trailer wiring harness the right part is #C56225.

view full answer...

Answer 2

Hello Greg, Great question, and yes level towing is important. The average height for a mid-size to full-size travel trailer is 22 to 28 inches, the average height for an F-350 with 4 wheel drive is 20–24 inches, with that being said you will most…

view full answer...

Answer 3

Sure! It's a Draw-Tite Trailer Hitch item #75291 that fits 2005 - 2015 Nissan Xterra's.

view full answer...

Answer 4

One way to determine the lift and jack height you need would be to measure the jack you currently have on your 2018 Intech Luna RV. If this is not possible, or you still aren't sure, you can also determine the correct jack using the coupler…

view full answer...

Answer 5

I have a solution for you but I'm not aware of a bolt on safety chain bracket or clevis. However you can simply take a safety chain set like the 42" Long Safety Chain with 3/8" Clevis Hook (15,000 lbs) #337BSC3842 and use a grade 8 bolt…

view full answer...

Answer 6

I hope I am fully understanding that you want to have both a 4-way and 7-way on the back of your 2007 Nissan Xterra. The Curt T-Connector Vehicle Wiring Harness #C56226 is the correct harness to give you a 7-way, but the Replacement Harness #118263…

view full answer...

Answer 7

Thanks for writing in Steve. For the 2023 Nissan Frontier I recommend our etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e98869. The weight capacity of this hitch is 500 pound tongue weight, and a 5,000 pound…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Replacement Curt Trailer Hitch Receiver Hardware for 2008 Nissan Xterra

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching