Comparing American Trailer Wheel Center Caps AM90092 and AM90091

Question

Question:

What is the difference of the two part #s listed above?

asked by: Mike

0

Expert Reply:

The difference is the size wheel each would fit. Center Cap # AM90092 is designed for 16 inch diameter wheels with 6 or 8 hole bolt patterns.

Center Cap # AM90091 is designed for 15 inch wheels with a 5 hole bolt pattern.

expert reply by: Michael H

0

Answer 1

I spoke with my contact at Americana and they told me that the Americana Trailer Wheel Center Cap, part #AM90091, will fit all 15 inch wheels regardless of the lug bolts, as long as the pilot hole is 3.19 inches diameter.

view full answer...

Answer 2

You will need to get the other bearing number from inside your current hubs before we can pick you out replacement hubs. Most likely the outer bearing you pulled is a LM67048 and the inner you have is a 25580 which would mean that the #8-201-5UC3…

view full answer...

Answer 3

The center cap on a trailer wheel like the Aluminum Hi-Spec Series 6 Trailer Wheel - 15" x 6" Rim - 5 on 4-1/2 #AM22651 will have a screw on the front to remove without removing the tire or wheel. You actually need to remove the cap…

view full answer...

Answer 4

I like the chrome wheel cap #AM90091 better with it, but it is really a personal preference. The Stainless steel #AM90175 would also work great for your #AM20537 Dexstar silver wheel.

view full answer...

Answer 5

The Americana Trailer Wheel Center Cap - Chrome #AM90091 is designed to fit 15 inch diameter wheels like #AM20455 that have a 5-hole bolt pattern and 3.19 inch pilot diameter. If this matches the wheels you have on your 2008 Starcraft Trailer, then…

view full answer...

Answer 6

The Aluminum Hi-Spec Series 6 Trailer Wheel #AM22651 does include its own center cap. So you will not need to use any other cap. The wheel is designed to work with 1/2-20 60-degree lug nuts and you can use a basic Lug Nut #CE11051.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Comparing American Trailer Wheel Center Caps AM90092 and AM90091

Continue Researching