Lug Nut Covers for Monaco MH on Workhorse W22 chassis 22.5 Wheels

Question

Question:

I cant seem to find the appropriate size lug nuts that hold on the wheel covers and the cover for the lug nuts also. I have a Monaco Monarch 37foot gasser which rides on a 2005 Workhorse W22 chassis and the wheel size is 22.5.

asked by: Carlos C

0

Expert Reply:

I looked up the lug nut size of the 2005 Workhorse W22 chassis that you have and since it has 33 mm lug nuts the lug covers you'd need are the part # PXSP33. We don't have this size lug nut though.

expert reply by: Jameson C

0

Answer 1

If the 33 mm Wheel Masters Lug Nut Covers #WM9005-6 were too big then you may need the 7/8" Covers #WM8019, 1" Covers #WM8010 or the 1-1/16" Covers #WM8011. I'm not sure what size lugs are used for your Workhorse W-22 Chassis but…

view full answer...

Answer 2

The best trailer hitch we have for your Workhorse W-22 Chassis is the Draw-Tite Ultra Frame Trailer Hitch Receiver part #41990-16. In order to fit the Ultra Frame to your Workhorse you will need to modify the brackets and crosstube to better suit…

view full answer...

Answer 3

Starting with the brake controller itself, I highly recommend the Tekonsha Prodigy P2 #90885. This is an excellent proportional controller that will activate your trailer's brakes at the same time and with the same intensity that you apply to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

Thanks for the information Kevin! To flat tow your 2025 Ford Bronco with a standard bumper and LED lights, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect item #e84ZR Base…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Lug Nut Covers for Monaco MH on Workhorse W22 chassis 22.5 Wheels

Product Page this Question was Asked From

Continue Researching