Dimensions of Wheel Chock Included w/ Erickson EM09160 ATV e-Track Tie Down Kit

Question

Question:

What are the dimensions of the metal wheel chock itself? What is the distance between mounting holes front to back and side to side?

asked by: Shaun H

0

Expert Reply:

The chock included with the # EM09160 Tie Down Kit is 5-3/16 inches wide, 8 inches long and 2-1/8 inches tall. The mounting holes are 4-1/2 inches across, measured center to center. The closer set of holes are 2 inches apart, with the distance from the first hole to the third hole being right at 6-1/2 inches, also measured center to center. You can see these dimensions in the provided photo I've edited for you.

I've also linked to a description video for the tie-down kit.

expert reply by: Mike L

0

click to enlarge

Answer 1

I think ideally you'd use two kits of the Erickson ATV E-Track Tie-Down Kit #EM09160 to secure them properly. I'd say on normal roads this is a great idea (using two kits), but on a rough road it's basically a requirement so that you…

view full answer...

Answer 2

Hey Raymond, yes we do have backing plates that can be used with the Erickson Wheel Chock kit part #EM09160 like with the #e89RR. These also can be used with decking boards. What kind of SXS do you have?

view full answer...

Answer 3

Before you purchase a weight distribution you need to make sure the trailer manufacturer recommends using a system on the trailer. A lot of aluminum trailers cannot bear the stress a weight distribution system puts on the frame like steel trailers…

view full answer...

Answer 4

Not all aluminum trailer frames are strong enough for use with a steel weight distribution (WD) system. It is possible that the stronger steel WD components could put too much stress on the frame. If your trailer has an aluminum frame you'll…

view full answer...

Answer 5

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 6

We do have a nice selection of bungee cords and tie-down straps, if you already have a spot where you can anchor them. Personally, I prefer tie-down straps with ratchets. For example, the Erickson Ratchet Tie-Down Straps w Flat Hooks - 2" x…

view full answer...

Answer 7

Hi Rick, I'm so sorry that happened with your ATV, it sounds really scary! To secure it to your tilt trailer and keep that from happening again, the etrailer E Track Wheel Tie Down Straps w/Roller Idlers part #e64PR you were looking at will do…

view full answer...

Answer 8

Hi Dave; that somewhat depends on the actual tire size but I would say a 4' section #e85VR is the minimum with a 5' #e25VR giving you a little more versatility with the #e64PR mounting position if you have the room for it. Both of these can…

view full answer...

Answer 9

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Answer 10

The safest way to secure a 4-wheeled vehicle like a golf cart in a truck bed is to use wheel nets that secure to the truck bed in some manner. The Erickson E-Track Tie-Down Kit #EM09160 is one option that is similar to the Pack 'Em kit you…

view full answer...

Answer 11

The correct brake controller harness for your 2023 Ford E-350 to install a Tekonsha Prodigy P3 part #90195 is the part #22292. The connector on your E-350 is in a really unusual location behind the vents above the stereo. To see how to access it…

view full answer...

Dimensions of Wheel Chock Included w/ Erickson EM09160 ATV e-Track Tie Down Kit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching