Trailer Hitch for 2014 Subaru Forester That Does Not Have Vibration or Rattling

Question

Question:

Hello, I just had a Curt 13399 installed by a hitch shop today. They said this hitch is the one I should use for my 2014 XT. But as I was driving home I notice a vibration in through whole car at 1300-1500rpm and became aware of the issue of the welded gusset. The shop offered to grind the gussets... which I obviously refused. I want them to find a compatible hitch which seems complicated unless going for much more expensive brands and increased lead time. I was wondering if the CU64FR would be compatible with the 2014 XT without conflicting with the dual exhaust hangers?

asked by: Jeandm

0

Expert Reply:

The Curt Trailer Hitch Receiver # CU64FR fits your 2014 Subaru Forester, and is the updated version of the 13399, though it does have the same welded gussets and it is possible to still conflict with the dual exhaust hanger.

We have not seen any complaints at all about this vibration occurring with the Draw-Tite Trailer Hitch Receiver # 76182, so that would be the other option I recommend.

expert reply by: Kyle S

0

Answer 1

Hey Jacob, the Kuat Beta bike rack part #B202-2 is designed for only fitting 2 inch hitches and does not come with an adapter to also fit a 1-1/4 inch hitch. The version of this rack that fits the 1-1/4 inch hitch is the part #B202-114. For a similar…

view full answer...

Answer 2

Hey Jacob, yes our Curt hitch part number #C13144 is the same as the Curt part number 13144.

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #CU64FR is going to be very similar to the Draw-Tite Max-Frame Trailer Hitch Receiver part #76182 which are both fits for a 2017 Subaru Forester. In regards to the Draw-Tite, the distance from the ground to the…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver part #CU64FR and the Draw-Tite Max-Frame Trailer Hitch Receiver part #76182 will have a concealed look therefore only the receiver tube opening will be shown once installed. In regards to the heat shield, this must be…

view full answer...

Answer 5

We don't have the items kitted, but I'd be happy to recommend a hitch, wiring harness, ball mount and trailer ball for you. For a hitch, I'd recommend either the Curt Class III #C13144 or the Class III #CU64FR. Both hitches have the same…

view full answer...

Answer 6

You could do that if you wish, you'll just want to make sure that the heat shield is NOT sandwiched between the hitch and the chassis of the vehicle at any point. We frequently hear from folks with concerns about the vehicle being harmed because…

view full answer...

Answer 7

The primary difference between the two is that once installed, the #C13144 will be completely visible from the rear of the vehicle. The #CU64FR is designed a bit differently, the hitch crossbar will be concealed behind the bumper with the only…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hello Julie, It would all depend on where your fenders sit. Most of the front fenders are short enough for the Hollywood Racks Crosstrack Bike Rack for 1 Bike - 1-1/4" and 2" Hitch - FREE Loading Ramp #HLY36RR (promo part number for limited…

view full answer...

Trailer Hitch for 2014 Subaru Forester That Does Not Have Vibration or Rattling

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching