Height of TorkLift StableLoad Suspension Upgrade for Upper Overload Springs # TLA7200

Question

Question:

What is the thickness of the mounting bracket and the rubber stop?

asked by: Phil L

1

Helpful Expert Reply:

The thickness of the #TLA7200 block itself is 2.25" in height. The height of the anti rock plate is 9/16" in height.

expert reply by: Jameson C

1

Answer 1

From the looks of the photo you have attached it appears you have a lower overload spring, not an upper overload spring that is required for the TorkLift StableLoad Suspension Upgrade for Upper Overload Springs part #TLA7200 to work. This kit will…

view full answer...

Answer 2

Hey Bob, congrats on a setting up a new camper! Out of all of those options you'll also need to consider daily driving comfort unless that camper is a permanent addition to your truck bed. Listed below are a brief breakdown of each and a…

view full answer...

Answer 3

Here is a list of the bump stop replacements we have which fit your 2024 Ford F-350. If you can tell me how you plan to use your F-350 I can give you my personal recommendation for the option which works best for you. Timbren Front 2WD #TFF350SD2 4WD…

view full answer...

Answer 4

The TorkLift StableLoad Suspension Upgrade part #TLA7200 could engage with your overload leaf spring as soon as they are installed even without any additional weight present depending on your setup which means they will have a negative effect on your…

view full answer...

Answer 5

I am happy to report that the TorkLift StableLoad Suspension Upgrade #TLA7200 does not require drilling on your 2022 Ford F-250 super duty. I went ahead and attached a photo of from the instructional manual for you to check out. It is important to…

view full answer...

Answer 6

The TorkLift StableLoad Suspension Upgrade Kit #TLA7200 works on both 2WD and 4WD versions of the 2019 F-350 that has a factory leaf spring suspension and an upper overload spring. These rubber block springs replace the truck's factory bump stop…

view full answer...

Answer 7

The pin weight of a 5th wheel trailer will usually be around 20% of the trailer's gross trailer weight (GTW) rating. The only real way to find the loaded pin weight of your 5th wheel trailer would require access to a commercial scale used to…

view full answer...

Answer 8

I always recommend SumoSprings over Timbrens for any vehicle that is not being used as a work truck. SumoSprings have two mounting points that only come together when a heavy load is placed on them. Timbrens will affect your daily driving and will…

view full answer...

Answer 9

We have many styles and sizes of trailer wheel lug nuts shown on the linked page. These are offered in either 60-degree or 90-degree coned profile, in zinc, chrome or stainless and for four different wheel stud diameters. Just click on the feature to…

view full answer...

Answer 10

The difference between the upper and lower Stableloads is the vehicle setup and because of that you can't install both at same time. The upper StableLoad like the part #TLA7200 is for versions of the 2021 Ford F-350 that have upper overload…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Height of TorkLift StableLoad Suspension Upgrade for Upper Overload Springs # TLA7200

Product Page this Question was Asked From

Continue Researching