Roof Vent Cover for MaxxAir MaxxFan Plus on Grand Design Solitude

Question

Question:

want to leave vent open so looking for cover that I can do that with

asked by: Robert R

0

Expert Reply:

If you've got a Maxx Air MaxxFan Plus like the # MA00-04751KSX you can use the MaxxAir FanMate RV and Trailer Roof Vent Cover - 25" x 18-1/8" x 10-1/4" - Smoke # MA00-955003, which is designed to fit 2015 and newer MaxxFan and MaxxFan Plus roof vents with mounting tabs. This will allow you to keep your vent open and running no matter what the weather is like outside.

I've also linked a review video of this part and the other available colors of this vent cover in case you're looking for something different.

expert reply by: Erik B

0

Answer 1

We don't carry the Von Weise brand so we can't get the replacement motors like you mentioned. Best option we would be a new setup altogether with a motor like the #LG-1.

view full answer...

Answer 2

When it come to wiring your Atwood GC6AA-9E hot water heater, you're going to want to go with a wire that's sized to accommodate the heater's current requirement. For example, a 20-amp hot water heater needs 12-gauge wire, a 25-amp hot…

view full answer...

Answer 3

The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat #MA00-06200K that you referenced needs a 12 volt power source so you are going to need to get 12 volts from the trailer's battery or circuit breaker panel so that it can operate. While the…

view full answer...

Answer 4

I went to the warehouse and measured the Free-Swinging RV Cabinet Hinges #37270655 and drew up a little diagram of the dimensions below. If you have any other questions or need another dimension just let me know.

view full answer...

Answer 5

Based on what you described wanting the MaxxAir MaxxFan part #MA00-04751KSX is your best option. This has a 4 speed fan, a powered lift, and has no thermostat. I attached a review video for this for more info as well.

view full answer...

Answer 6

We have a white MaxxFan vent roof with power lift and fan with the part #MA00-04751KSX which also does not have a ceiling garnish.

view full answer...

Answer 7

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Roof Vent Cover for MaxxAir MaxxFan Plus on Grand Design Solitude

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching